INTELMANN MARKEN SHOP

Duct clamp for pulling together air duct connection profiles For connecting rectangular air duct systems Suitable for all profile sizes incl. screwed-in screw M8 x 25 mm Material thickness 3 mm Material: galvanised steel The duct clamp is placed over the air duct profiles and fastened with the screw. The profiles are pressed against each other by tightening the clamp. Duct clamps should be installed so that the free length between 2 connection points does not exceed 200 mm. The hexagon head screw must be tightened to approx. 7 Nm.

VERSATILE USE: Aluminium adhesive tape is perfect for joints and seals in insulation, wiring and pipe work. It can also be used for repairs to metal surfaces such as vehicle bodies and guttering. No toolbox should be without it!STRONG ADHESIVE: Adheres immediately to metallic surfaces and provides an airtight and watertight seal. Thanks to the long-lasting adhesive, this aluminium tape provides reliable insulation, whether it is used indoors or outdoors. Heat-resistant from -30 °C to +130 °CEASY TO APPLY: Simply cut to the desired size, remove from the backing paper and apply.Aluminium adhesive tape for sealing duct or corrugated pipe connections Length: 45m Width: 50mm Thickness: 30µ Application range from -30 to +130°C

Spiral duct for the installation of ventilation systemsSpiral duct ØD = inner diameter [mm]Length 1000 mmMaterial: Galvanised sheet steelDesign in accordance with DIN EN 12237Tightness class D according to DIN EN 1507 (highest class of the standard)Intelmann spiral duct Application areas: The Intelmann spiral duct or spiral seam duct is used for air routing of extract air, outside air, exhaust air and supply air in centralised domestic ventilation or controlled domestic ventilation with heat recovery. The ventilation duct is made of galvanised sheet steel. The diameter refers to the internal diameter of the duct. Connecting the Intelmann spiral ducts in the ventilation system: Nipples or pipe connectors are used to connect the spiral ducts in a ventilation system. Fittings such as bends, branch pieces or T-pieces can be connected directly to the spiral duct. Sockets are used to connect fittings (bends / branch pieces / T-pieces) to each other. A spiral duct is compatible with all other fittings with the same diameter. Two spiral ducts are connected with a nipple.

Flat trunking nipple connector made of galvanised sheet steel For direct connection of duct to duct Flat duct system for controlled domestic ventilation or extractor fans 50 mm height Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1 Insertion depth per side 40 mm. On request: Special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.

Application For fastening spiral ducts Your advantages Suitable clamping ranges for all spiral ducts (standard) Catch lock: quick and easy insertion and fastening of the pipe using the catch lock up to a nominal pipe diameter of 450 mm, from a nominal pipe diameter of 500 mm with M8 hexagon head screw Easy installation of the ventilation clamp thanks to the wide opening angle of the pipe clamp Stiffening of the ventilation clamp due to bead geometry Easy engagement of the screw plug with a fingertip High level of safety due to edge-locking suspension opening No uncontrolled opening after engaging thanks to safety catch lock The easy-to-engage lock allows the pipe clamp to be opened and closed with just one hand With highly elastic DÄMMGULAST® sound insulation insert: average sound level improvement of 18 dB(A) M8/M10 threaded connections customised to the application This product has been awarded the "pipe fastening quality mark" and is subject to external monitoring in accordance with RAL-GZ 655-B

Disc valve for return air Steel, powder-coated, white RAL 9010 The volume flow can be infinitely adjusted using the adjustable disc Mounting ring / installation frame included Large adjustment range Low noise level Quick and easy to install The disc valve is made of powder-coated sheet steel. The standard colour is white (RAL 9010). A good seal is achieved by combining the valve body with a spring lock (bayonet lock) and sealing tape. The disc valve has an adjustable, centrally arranged, rotating valve disc. It has a low noise level. Exhaust air valve: Designed for exhaust air operation in residential buildings and offices as well as for toilet ventilation. Supply air valve: Designed for supply air operation in homes and offices.

Nipple for connecting spiral ducts Insertion depth = 40 mm Design in accordance with DIN EN 12237 Tightness class D according to DIN EN 1507 (highest class of the standard) Material galvanised steel

Hose clamp / band clamp / clamping clamp Clamping ranges: 50 to 525 mm Band width: 9 mm Stainless steel Worm thread with pull-tilt mechanism for mounting flexible hoses z.B. for aluminium flexible pipe / aluminium flexible hose / ventilation pipe / insulated flexible hoses / laminate hoses / air conditioning hoses

Socket for connecting moulded parts (bends, T-pieces, branch pieces, reducers, etc.) Insertion depth = 40 mm Design in accordance with DIN EN 12237 Tightness class D to DIN EN 1507 (highest class of the standard) Material galvanised steel The sleeve is used to connect moulded parts. It is NOT suitable for connecting a spiral duct to another duct. The sleeve can be used to connect a spiral duct bend and a T-piece.

MEZ-PLAST 580, 310 ml cartridge, silver-grey Sealing compound for sealing air duct systems and technical installations without silicone an alternative to soldering very good adhesion to all metals Fast curing sealant High chemical resistance Product properties: good adhesion to greasy, oily substrates and all metals Permanently elastic resistant to ageing, weathering and UV radiation antibacterial and fungicidal (against fungal attack) toxicologically harmless Resistant to many chemicals fulfils the hygienic requirements for use in for use in clean rooms and the specifications of the VDI 6022 guideline. can be used on lightly oiled, corrosion-preserved metals without degreasing without silicone, without nitrogen CFC-free no AOX components no lead compounds no mercury compounds no chromium compounds MEZ-PLAST is lead- and chromate-free and therefore food-safe according to the law Technical data Raw material base: acrylic resin, solvent-curing Curing time: approx. 4 mm in the first 24 h at +23°C and 50% r.F. Temperature resistance: - 40°C to +80°C (permanent) - 40°C to +100°C max. 1 h Processing temperature: +2°C to +60°C Shore A hardness: 38 Density: 1.05 g/m3 Primer: no Skin formation time: 10 min. at 23°C and 50% r.F. Coating compatibility: yes, preliminary tests required Paintability: yes, preliminary tests required Shelf life: 12 months Storage: protect from frost Flash point: below +21°C /- 4°C Hazard class: A1 Area of application: Sticks and adheres to all metals for sealing in ventilation ducts and plant construction Bonding and sealing in clean rooms, chip production, etc. Notes: - MEZ-PLAST is ready to use and can be applied without pre-cleaning and degreasing the areas to be sealed using a brush, - spatula or spraying equipment. - can be painted over after curing - A slight shrinkage may occur due to evaporation of the solvents contained.

Disc valve for the supply air Steel, powder-coated, white RAL 9010 The volume flow can be infinitely adjusted using the adjustable disc Mounting ring / installation frame included Large adjustment range Low noise level Quick and easy to install The disc valve is made of powder-coated sheet steel. The standard colour is white (RAL 9010). A good seal is achieved by combining the valve body with a spring lock (bayonet lock) and sealing tape. The disc valve has an adjustable, centrally arranged, rotating valve disc. It has a low noise level. Exhaust air valve: Designed for exhaust air operation in residential buildings and offices as well as for toilet ventilation. Supply air valve: Designed for supply air operation in homes and offices.

Intelmann plastic air duct for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealants or solvents.Made of white plastic and temperature-resistant up to 60 °CFormat: 55х110 mm or 55x220 mmLength: 1000 mm

Elbow for spiral duct Insertion length l = 40mm Galvanised steel 275 g /m² with EPDM double lip seal Tightness class D according to DIN EN 12237, highest tightness class for air ducts The bend is inserted directly into the spiral duct From a diameter of 224 mm, the bend is manufactured as a segmented bend

Flat trunking with fixing strip made of galvanised sheet steel, width 100 - 300 mm, height 50 mm. The width and height specifications refer to the internal dimensions of the trunking. The total length of the trunking is L=1000 mm. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled domestic ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. The Intelmann flat duct system is designed according to the socket-nipple principle. This means that all moulded parts can be inserted into the ducts. Flat channels are connected to each other with nipples. Moulded parts, on the other hand, are connected to each other with a sleeve. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 Connection of duct and fitting with plug-in connection, sleeve and nipple. Insertion lengths generally 40 mm, all lengths without insertion lengths. Round connections to flat duct and spiral duct as well as spiral duct moulded parts with dimensions according to DIN EN 1506, all round nipples with EPDM double lip. On request: special parts / dimensions, deviating heights, also in stainless steel 1.4301 and 1.4571 and aluminium.

Intelmann plastic air duct for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealants or solvents.Made of white plastic and temperature-resistant up to 60 °CFormat: 55х110 mm or 55x220 mmLength: 1000 mm

Flat trunking with internal reinforcement and fixing strip made of galvanised sheet steel, width 180 - 300 mm, height 50 mm. The width and height specifications refer to the internal dimensions of the trunking. The total length of the trunking is L=1000 mm. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled domestic ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. The Intelmann flat duct system is designed according to the socket-nipple principle. This means that all moulded parts can be inserted into the ducts. Flat channels are connected to each other with nipples. Moulded parts, on the other hand, are connected to each other with a sleeve. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 Connection of duct and fitting with plug-in connection, sleeve and nipple. Insertion lengths generally 40 mm, all lengths without insertion lengths. Round connections to flat duct and spiral duct as well as spiral duct moulded parts with dimensions according to DIN EN 1506, all round nipples with EPDM double lip. On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium.

Flat trunking made of galvanised sheet steel Width: 100 to 300 mm, height: 50 mm The width and height specifications refer to the internal dimensions of the trunking The total length of the trunking is L = 1000 mm The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled (domestic) ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. We recommend our version with internal reinforcement for this purpose. To seal the joints, we recommend our aluminium adhesive tape or aluminium-laminated cold-shrink tape. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 On request: Special parts / dimensions, different heights, also stainless steel V2A (1.4301) and V4A (1.4404) and aluminium

Intelmann plastic connector for connecting flat ducts (sleeve) Not suitable for connecting moulded parts (bends, T-piece, deflection piece), please use moulded part connector FKNK for this.Made of white plastic and temperature resistant up to 60° CSize: 55х110 mm or 55x220 mmType: Duct connector / sleeve

Pre-laminating tape 4 mm x 12 mm Length: 10m / 20m Colour: Grey without firmly laminated silicone film Material: closed-cell polyethylene foam Self-adhesive on one side Temperature resistance: from - 30 to + 80 °C fulfils the hygienic requirements for use in air conditioning systems in accordance with VDI 6022 Reduction of noise transmission Motion damping Condensation water resistance: very good Versatile sealing and sealing tape/ suitable for a wide range of industrial and construction applications

Flat duct socket connector for fittings made of galvanised sheet steel. For connecting moulded part to moulded part For connecting two pieces of moulding (bend with bend, bend with T-piece, etc.); NOT suitable for connecting flat duct to flat duct! Flat duct system for controlled domestic ventilation or extractor hoods; 50 mm height; Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1; Insertion depth per side 40 mm; On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.

Weather protection grille Ø 100 mm to Ø 315 mm type ADWSG Aluminium weather protection grille for outside For exhaust air from extractor bonnets or exhaust air dryers Absolutely weatherproof With insect screen made of fine-meshed stainless steel mesh With rigid louvres Round connection on the back for connecting a ventilation duct or hose Installation:Insert the weather protection grille with the connection piece into the ventilation duct and fasten with screws.

Weather protection grille Ø 100 mm to Ø 150 mm type WSHE Stainless steel V2A Design weather protection grille for outside, weatherproof With self-closing flap, damped flap stop, no rattling due to metal on metal With rubber sealing tape for perfect connection to external façade, screws for installation included in scope of delivery Round connection on the back for connecting a ventilation pipe or hose Installation:Attach the rubber seal to the outer edge of the bonnet. This sometimes requires a little patience. Then insert the weather protection grille with the connection piece into the ventilation duct and fix it directly to the wall using the screws provided. For better fastening in the ventilation duct, there are clamping lugs on the spigot of the bonnet.

Filter basket stainless steel V2A with cone filter class G3 suitable for 2-part intake tower made of stainless steel AT2A-S Stainless steel (V2A) consisting of retaining ring, round cord filter holders, wire basket and G3 filter Filter basket with conical filter V2A, consisting of retaining ring, round cord filter holders, wire basket and G3 filter. The filter basket is inserted into the KG pipe (orange) and the intake tower made of stainless steel 2-part smooth pipe with louvre bonnet is placed over the KG pipe.

Filter / Replacement filter class G3 for Intelmann intake towerCylindrical replacement filter for the Intelmann intake tower. The filter basket is NOT included in the scope of delivery!

Intelmann plastic air duct bend 90° flat to round for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealant or solvents.Made of white plastic and temperature resistant up to 60 °CFormat: 55х110 mm or 55x220 mmType: Bend 90° flat duct to round 100-125 mm

The insulating conduit consists of a glass fibre reinforced aluminium laminate outer jacket with a 25 mm insulating layer of insulating wool. The insulating hose is equipped with a barrier layer. The barrier layer simplifies installation and prevents direct contact with the insulating wool. Thermal insulation is used to prevent condensation and reduce heat and cold loss. The diameter specification refers to the inner diameter of the insulating hose. A 100 mm spiral duct / aluminium flex duct can be insulated with a DIS100. In practice, however, it is much easier to insulate the pipe if you select the insulating hose one size larger. ASSEMBLY The insulating hose is simply pulled over an existing pipe (e.g. spiral duct). This provides the pipe with diffusion-tight protection against moisture and thermal influences. APPLICATION Insulation of ventilation systems Air conditioning systems To reduce heat loss To prevent / eliminate condensation TECHNICAL DATA Item number: DIS{Ø} Temperature range: -30 ⁰C to 140 ⁰C Operating pressure: up to +2000 Pa Air velocity: irrelevant Bending radius: 0.54 x Ø + 25mm Diameter range: 80 - 250 mm MATERIAL CONSTRUCTION Insulation layer: Polyester Insulating wool: 25mm, 16kg/m³ Outer sheath: Aluminium / poly laminate R-value insulating wool: 0.65 m² K/W (ASTM C177-76) Standard colour: Aluminium / Silver Standard length: 10 metres

The connecting sleeve is used to connect a fan to a round air duct (spiral duct) with the same diameter. At the same time, it absorbs vibrations from the fan to the ventilation duct. The advantage of this type of connection is that the fan can be removed from the air duct system at any time for replacement or repair. The sleeve is made of galvanised sheet steel, fitted with a foam rubber seal with a thickness of 6 millimetres on the inside. There are two M6 screws at the ends of the adjusting ring for fixing the sleeve: screws and nuts are part of the product.

Intelmann plastic connector for connecting flat ducts (sleeve) Not suitable for connecting moulded parts (bends, T-piece, deflection piece), please use moulded part connector FKNK for this.Made of white plastic and temperature resistant up to 60° CSize: 55х110 mm or 55x220 mmType: Duct connector / sleeve

Slide-in backflow flap / internal non-return flap Nominal width 100 mm to 200 mm Opens smoothly, low pressure loss Closes securely, no noise, no rattling The damper is inserted into the ventilation duct For vertical and horizontal installation Housing: Galvanised steel Damper blade: Aluminium Shaft and spring: Stainless steel The non-return damper is used in round ventilation ducts to prevent air backflow. The casing is made of galvanised sheet steel. The damper blades are made of aluminium and the shaft and spring are made of stainless steel. The internal rubber seal reduces noise. The outer foam strip provides a good seal and secures the non-return flap in the pipe. The non-return damper is designed for operation at ambient temperatures up to 60°C, for the transport of clean air, free of coarse dust, grease, chemical vapours and other impurities.

INTAKE TOWER MADE FROM POLISHED STAINLESS STEELThe intake tower is made of high-quality, solid stainless steel (V2A). To give the intake tower that certain something, the surface has been polished to 220 grit. Neither wind nor weather can harm this intake tower.The simple and exclusive design makes the intake tower a real eye-catcher, even in the entrance area of your home!The Intelmann intake tower series impresses with its simple elegance paired with great functionality: The integrated stop bead in the main pipe is used to hold the filter basket at the top end of the pipe. The filter can be changed without tools.Excellent features of the intake towerSturdy and durable construction made of solid, high-quality stainless steelCorrosion-resistant and robustStainless steel V2AFinishing: polished surface (220 grit)UV and weather resistantEasy to cleanIntelmann quality productTECHNICAL DATA The stainless steel 2-piece smooth tube intake tower with louvre bonnet is suitable for all standard soil pipes that are connected to your ventilation system, geothermal heat exchanger or chimney.Suitable for the following soil pipes:KG pipe (orange)KG2000 (green)HT pipe (grey)POLO-KAL (blue).The intake tower is supplied in two parts and consists of a smooth pipe and a louvred cover.The smooth tube and louvred bonnet are made of V2A stainless steel (220 grit polished). The louvre cover has an inserted bird protection grille (mesh size 10 x 10 mm). Installation is quick and uncomplicated:Allow the ground tube to protrude at least 30 cm - 40 cm above ground level.Cut off the sleeve (the thick end of the ground tube) Place the smooth pipe over the soil pipeInsert the louvre cap into the smooth pipeDONE!!!!ATTENTION!!! The AT2A-S100 / AT2A-S100-500 only fits into the KG pipe socket and is not placed over the KG pipe! If the intake tower is used for the intake of outside air, a filter basket including a coarse dust filter should also be installed in order to catch heavy impurities from your ventilation system.The filter basket is inserted into the smooth tube of the intake tower just below the louvre bonnet and is held in place by a stop bead. Replacing the filter is correspondingly straightforward.No additional installation material, tools or fixings are required, as the ground pipe ensures that the intake tower stands securely.Volume flow:AT2A-S100 / AT2A-S100-500 = 175 m³/hAT2A-S110 / AT2A-S110-500 = 270 m³/hAT2A-S125 / AT2A-S125-500 = 270 m³/hAT2A-S160 / AT2A-S160-500 = 430 m³/hAT2A-S200 / AT2A-S200-500 = 690 m³/hAT2A-S250 / AT2A-S250-500 = 1000 m³/h AT2A-S315 / AT2A-S315-500 = 1600 m³/hNote: When the exhaust air system is at a standstill, moisture, snow or dust can enter the pipe system. In order to prevent moisture from being sucked in with outside air intake, the air velocity in the free cross-section must not exceed 2 m/s.