Flat duct transition piece to asymmetrical spiral duct 140 mm 80 mm
€27.13
Available immediately, delivery time: 1-3 working days
Product information "Flat duct transition piece to asymmetrical spiral duct 140 mm 80 mm"
- Flat duct transition piece to spiral duct
- Pipe nipple to EN1506 with double lip seal for direct connection to spiral duct
- Duct nipple for direct insertion into flat duct system
- Material: galvanised steel
- The Intelmann flat duct system is designed according to the socket-nipple principle
- Flat ducts are connected to each other with flat duct nipple connectors
- Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve
- This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Allgemeines Warnzeichen
Warnung vor Handverletzungen
Warnung vor Absturzgefahr
Customers also bought
Flat trunking made of galvanised sheet steel Width: 100 to 300 mm, height: 50 mm The width and height specifications refer to the internal dimensions of the trunking The total length of the trunking is L = 1000 mm The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled (domestic) ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. We recommend our version with internal reinforcement for this purpose. To seal the joints, we recommend our aluminium adhesive tape or aluminium-laminated cold-shrink tape. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 On request: Special parts / dimensions, different heights, also stainless steel V2A (1.4301) and V4A (1.4404) and aluminium
Flat trunking nipple connector made of galvanised sheet steel For direct connection of duct to duct Flat duct system for controlled domestic ventilation or extractor hoods 50 mm height Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1 Insertion depth per side 40 mm. On request: Special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Flat duct socket connector for fittings made of galvanised sheet steel. For connecting moulded part to moulded part For connecting two pieces of moulding (bend with bend, bend with T-piece, etc.); NOT suitable for connecting flat duct to flat duct! Flat duct system for controlled domestic ventilation or extractor hoods; 50 mm height; Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1; Insertion depth per side 40 mm; On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Spiral duct for the installation of ventilation systemsSpiral duct ØD = inner diameter [mm]Length 1000 mmMaterial: Galvanised sheet steelDesign in accordance with DIN EN 12237Tightness class D according to DIN EN 1507 (highest class of the standard)Intelmann spiral duct Application areas: The Intelmann spiral duct or spiral seam duct is used for air routing of extract air, outside air, exhaust air and supply air in centralised domestic ventilation or controlled domestic ventilation with heat recovery. The ventilation duct is made of galvanised sheet steel. The diameter refers to the internal diameter of the duct. Connecting the Intelmann spiral ducts in the ventilation system: Nipples or pipe connectors are used to connect the spiral ducts in a ventilation system. Fittings such as bends, branch pieces or T-pieces can be connected directly to the spiral duct. Sockets are used to connect fittings (bends / branch pieces / T-pieces) to each other. A spiral duct is compatible with all other fittings with the same diameter. Two spiral ducts are connected with a nipple.
MEZ-PLAST 580, 310 ml cartridge, silver-grey Sealing compound for sealing air duct systems and technical installations without silicone an alternative to soldering very good adhesion to all metals Fast curing sealant High chemical resistance Product properties: good adhesion to greasy, oily substrates and all metals Permanently elastic resistant to ageing, weathering and UV radiation antibacterial and fungicidal (against fungal attack) toxicologically harmless Resistant to many chemicals fulfils the hygienic requirements for use in for use in clean rooms and the specifications of the VDI 6022 guideline. can be used on lightly oiled, corrosion-preserved metals without degreasing without silicone, without nitrogen CFC-free no AOX components no lead compounds no mercury compounds no chromium compounds MEZ-PLAST is lead- and chromate-free and therefore food-safe according to the law Technical data Raw material base: acrylic resin, solvent-curing Curing time: approx. 4 mm in the first 24 h at +23°C and 50% r.F. Temperature resistance: - 40°C to +80°C (permanent) - 40°C to +100°C max. 1 h Processing temperature: +2°C to +60°C Shore A hardness: 38 Density: 1.05 g/m3 Primer: no Skin formation time: 10 min. at 23°C and 50% r.F. Coating compatibility: yes, preliminary tests required Paintability: yes, preliminary tests required Shelf life: 12 months Storage: protect from frost Flash point: below +21°C /- 4°C Hazard class: A1 Area of application: Sticks and adheres to all metals for sealing in ventilation ducts and plant construction Bonding and sealing in clean rooms, chip production, etc. Notes: - MEZ-PLAST is ready to use and can be applied without pre-cleaning and degreasing the areas to be sealed using a brush, - spatula or spraying equipment. - can be painted over after curing - A slight shrinkage may occur due to evaporation of the solvents contained.
MEZ-PLAST 590 SMP, 300 ml cartridge, grey MEZ-PLAST 590 SMP is an elastic, fast-setting one-component sealant for HVAC applications, tested in accordance with DIN EN ISO 846.Application: Suitable for HVAC systems in accordance with VDI 6022 / EN 15780, as well as for grease exhaust air and clean rooms. With EC 1 Plus classification, MEZ-PLAST SMP fulfils the highest requirements for sustainable construction. Complies with DGNB 2018.Properties:Fungicidal and bactericidalNon-corrosiveQuickly tack-free surfaceFree from silicone and isocyanateVery low shrinkageGood weathering & ageing resistanceSolvent-freeSkin formation: Approx. 15 - 20 min.Curing: 3 - 4 mm on the 1st dayProcessing temperature: +5°C to +35°CTemperature resistance: -40°C to +90°CShelf life: 12 monthsREACH regulationSVHC ≤ 0.1 %MEZ-PLAST 590 SMP does not contain any substances of very high concern above 0.1%. PRODUCT HIGHLIGHTS: Low emission Silicone-free Free from solvents & isocyanateHigh temperature resistance
Self-tapping screws 4.2x13 mm with hexagon head and pressed-on washer, case-hardened galvanised steel, self-tapping DIN 7504 KThese screws are manufactured in galvanised steel. Self-tapping screws with 6KT head and pressed-on washer are characterised by their head shape (hexagon head with flange) and have a sheet metal thread. When you purchase a packaging unit of DIN 7504 K self-drilling screws, you receive 100 screws. Further important information about the article DIN 7504 Form K - Self-drilling screw with 6KT head with pressed-on washer : Weight per 100 pieces: 0.193 kg d: 4.2 mm; s: 7 mm; l: 13 mm; k: 4.1 mm; lp: 4.5 mm Self-drilling screws made of steel, electrogalvanised, high-quality industrial quality. Self-drilling screws for mounting sheet metal, ventilation ducts, flat ducts, fans, metal rails and car parts. The screws can be easily fastened with a cordless screwdriver without pre-drilling
Nipple for connecting spiral ducts Insertion depth = 40 mm Design in accordance with DIN EN 12237 Tightness class D according to DIN EN 1507 (highest class of the standard) Material galvanised steel