Butterfly valve with Belimo TF230 Ø 200 mm spring return
€217.29
Available immediately, delivery time: 1-3 working days
Product information "Butterfly valve with Belimo TF230 Ø 200 mm spring return"
- Shut-off damper steel, galvanised
- with EPDM sealing lips for airtight installation to DIN EN 12237 class D best class of this standard
- Damper blade with EPDM sealing lip tight-closing to DIN EN 1751 class 4 best class of this standard
- Damper blade with two bearings; damper with motorised bracket, rotatable for actuator mounting at any position, 360° around damper shaft
- With Belimo TF230 damper actuator with spring return
- Running time motor 75 s / 90°; running time emergency control function <25 s / 90°
- for open/close control of dampers, for 230 V, 2.5 NM torque, for dampers up to 1m² damper area
- The shut-off damper is inserted between two ventilation ducts
Technical data sheet Belimo TF230
Electrical data
Rated voltage AC 230 V
Rated voltage Frequency 50/60 Hz
Operating range AC 85...264 V
Power consumption in operation 2.5 W
Power consumption idle position 1.5 W
Power consumption Dimensioning 5 VA
Power supply / control connection Cable 1 m, 2 x 0.75 mm²
Parallel operation Yes (observe power data)
Functional data
Motor torque min. 2.5 Nm
Spring return torque min. 2.5 Nm
Motor direction selectable by mounting L / R
Direction of travel Emergency positioning function selectable by mounting L / R
Manual adjustment no
Angle of rotation max. 95°
Angle of rotation Note adjustable from 37% in 2.5% increments (with mechanical stop)
mechanical stop)
Running time motor 75 s / 90°
Running time emergency adjustment function <25 s / 90°
Motor sound power level 50 dB(A)
Axle drive Universal clamping block 6...12.7 mm
Mechanical position indicator
Service life min. 60,000 emergency positions
Safety class
Protection class IEC/EN II insulated
Protection class IEC/EN IP42
EMC CE in accordance with 2004/108/EC
Low Voltage Directive CE according to 2006/95/EC
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
Mode of operation Type 1.AA
Overvoltage category III
Rated impulse voltage Supply / control
Control
4 kV
Degree of pollution of the environment 3
Ambient temperature -30...50°C
Storage temperature -40...80°C
Ambient humidity 95% r.H., non-condensing
Maintenance maintenance-free
Weight approx.
Weight approx. 0.69 kg
Allgemeines Warnzeichen
Warnung vor Handverletzungen
Warnung vor Absturzgefahr
Customers also bought
Spiral duct for the installation of ventilation systemsSpiral duct ØD = inner diameter [mm]Length 1000 mmMaterial: Galvanised sheet steelDesign in accordance with DIN EN 12237Tightness class D according to DIN EN 1507 (highest class of the standard)Intelmann spiral duct Application areas: The Intelmann spiral duct or spiral seam duct is used for air routing of extract air, outside air, exhaust air and supply air in centralised domestic ventilation or controlled domestic ventilation with heat recovery. The ventilation duct is made of galvanised sheet steel. The diameter refers to the internal diameter of the duct. Connecting the Intelmann spiral ducts in the ventilation system: Nipples or pipe connectors are used to connect the spiral ducts in a ventilation system. Fittings such as bends, branch pieces or T-pieces can be connected directly to the spiral duct. Sockets are used to connect fittings (bends / branch pieces / T-pieces) to each other. A spiral duct is compatible with all other fittings with the same diameter. Two spiral ducts are connected with a nipple.