Butterfly valve with Belimo LM230A Ø 80 mm
€121.89
Available immediately, delivery time: 1-3 working days
Product information "Butterfly valve with Belimo LM230A Ø 80 mm"
- Shut-off damper: galvanised steel or stainless steel V2A
- with EPDM sealing lips for airtight installation to DIN EN 12237 class D best class of this standard
- Damper blade with EPDM sealing lip, tight-closing to DIN EN 1751 class 4, best class of this standard
- Damper blade with two bearings; damper with motorised bracket, rotatable for actuator mounting at any position, 360° around damper shaft
- With Belimo LM230A damper actuator for open/close control of dampers, for 230 V, 5 NM torque, for dampers up to 1m² damper area
- The shut-off damper is inserted between two ventilation ducts
Technical data sheet Belimo LM230A
Electrical data
Rated voltage AC 230 V
Rated voltage Frequency 50/60 Hz
Operating range AC 85...264 V
Power consumption in operation 1.5 W
Power consumption idle position 0.5 W
Power consumption dimensioning 3.5 VA
Power supply / control connection Cable 1 m, 3 x 0.75 mm²
Parallel operation Yes (observe power data)
Functional data
Motor torque min. 5 Nm
Direction of rotation Motor selectable with switch 0 (anti-clockwise) / 1
(clockwise rotation)
Manual adjustment Gear disengagement with push button, lockable
Angle of rotation max. 95°
Angle of rotation Note can be limited on both sides by adjustable
mechanical stops
Motor running time 150 s / 90°
Motor sound power level 35 dB(A)
Axle mounting Universal clamping block 6...20 mm
Mechanical position indicator, clip-on
Safety
Protection class IEC/EN II insulated
Protection class UL II insulated
Protection class IEC/EN IP54
Protection class NEMA/UL NEMA 2, UL Enclosure Type 2
EMC CE according to 2004/108/EC
Low Voltage Directive CE according to 2006/95/EC
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
Certification UL cULus according to UL 60730-1A, UL 60730-2-14
and CAN/CSA E60730-1:02
Mode of operation Type 1
Rated impulse voltage Supply /
Control
43 kV
Degree of pollution of the environment 3
Ambient temperature -30...50°C
Storage temperature -40...80°C
Ambient humidity 95% r.H, non-condensing
Maintenance maintenance-free
Weight approx.
Weight approx. 0.50 kg
Allgemeines Warnzeichen
Warnung vor Handverletzungen
Warnung vor Absturzgefahr
Customers also bought
Spiral duct for the installation of ventilation systemsSpiral duct ØD = inner diameter [mm]Length 1000 mmMaterial: Galvanised sheet steelDesign in accordance with DIN EN 12237Tightness class D according to DIN EN 1507 (highest class of the standard)Intelmann spiral duct Application areas: The Intelmann spiral duct or spiral seam duct is used for air routing of extract air, outside air, exhaust air and supply air in centralised domestic ventilation or controlled domestic ventilation with heat recovery. The ventilation duct is made of galvanised sheet steel. The diameter refers to the internal diameter of the duct. Connecting the Intelmann spiral ducts in the ventilation system: Nipples or pipe connectors are used to connect the spiral ducts in a ventilation system. Fittings such as bends, branch pieces or T-pieces can be connected directly to the spiral duct. Sockets are used to connect fittings (bends / branch pieces / T-pieces) to each other. A spiral duct is compatible with all other fittings with the same diameter. Two spiral ducts are connected with a nipple.