FLACHKANAL UND FORMTEILE VERZINKT
Das Intelmann Flachkanal- und Formteilsortiment hat eine besonders flache Bauweise. Die Höhe des Kanals beträgt 50 mm und eignet sich daher hervorragend um in der Filigrandecke oder im Estrichbeton verlegt zu werden. Damit der Kanal die Belastung aushält, muss der Flachkanal mit der vormontierten Innenversteifung benutzt werden. Alternativ kann die Innenversteifung auch separat erworben und in Eigenleistung in den Kanal eingeführt werden.
Zum Verbinden von zwei Flachkanälen wird ein „Flachkanalverbinder (Nippel)“ benötigt. Dieser wird in die Kanäle eingeschoben.
Formteile (Bögen, T-Stücke, Y-Stücke, etc.) werden direkt in den Kanal eingeschoben. Hierfür ist kein Verbinder notwendig.
Zwei Formteile werden untereinander mit einem „Formteilverbinder (Muffe)“ verbunden.
Flat trunking made of galvanised sheet steel Width: 100 to 300 mm, height: 50 mm The width and height specifications refer to the internal dimensions of the trunking The total length of the trunking is L = 1000 mm The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled (domestic) ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. We recommend our version with internal reinforcement for this purpose. To seal the joints, we recommend our aluminium adhesive tape or aluminium-laminated cold-shrink tape. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 On request: Special parts / dimensions, different heights, also stainless steel V2A (1.4301) and V4A (1.4404) and aluminium
Flat trunking with fixing strip made of galvanised sheet steel, width 100 - 300 mm, height 50 mm. The width and height specifications refer to the internal dimensions of the trunking. The total length of the trunking is L=1000 mm. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled domestic ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. The Intelmann flat duct system is designed according to the socket-nipple principle. This means that all moulded parts can be inserted into the ducts. Flat channels are connected to each other with nipples. Moulded parts, on the other hand, are connected to each other with a sleeve. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 Connection of duct and fitting with plug-in connection, sleeve and nipple. Insertion lengths generally 40 mm, all lengths without insertion lengths. Round connections to flat duct and spiral duct as well as spiral duct moulded parts with dimensions according to DIN EN 1506, all round nipples with EPDM double lip. On request: special parts / dimensions, deviating heights, also in stainless steel 1.4301 and 1.4571 and aluminium.
Flat trunking with internal reinforcement and fixing strip made of galvanised sheet steel, width 180 - 300 mm, height 50 mm. The width and height specifications refer to the internal dimensions of the trunking. The total length of the trunking is L=1000 mm. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled domestic ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. The Intelmann flat duct system is designed according to the socket-nipple principle. This means that all moulded parts can be inserted into the ducts. Flat channels are connected to each other with nipples. Moulded parts, on the other hand, are connected to each other with a sleeve. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 Connection of duct and fitting with plug-in connection, sleeve and nipple. Insertion lengths generally 40 mm, all lengths without insertion lengths. Round connections to flat duct and spiral duct as well as spiral duct moulded parts with dimensions according to DIN EN 1506, all round nipples with EPDM double lip. On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium.
Flat duct end cover Height = 50 mm Plug-in flat duct system Flat duct system for controlled domestic ventilation or extractor fan Material: galvanised steel The end cover is inserted directly into the flat duct
Vertical flat duct bend made of galvanised sheet steel. Area of application: Flat duct bends are used as connecting elements in supply and exhaust air ducts for controlled domestic ventilation. They can also be used in exhaust air ducts for extractor bonnets in the kitchen or as part of a supply air duct for fireplaces and stoves. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your duct system. The Intelmann flat duct system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Horizontal flat duct bend made of galvanised sheet steel. Area of application: Flat duct bends are used as connecting elements in supply and exhaust air ducts for controlled domestic ventilation. They can also be used in exhaust air ducts for extractor bonnets in the kitchen or as part of a supply air duct for fireplaces and stoves. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your duct system. The Intelmann flat duct system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Flat duct socket connector for fittings made of galvanised sheet steel. For connecting moulded part to moulded part For connecting two pieces of moulding (bend with bend, bend with T-piece, etc.); NOT suitable for connecting flat duct to flat duct! Flat duct system for controlled domestic ventilation or extractor hoods; 50 mm height; Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1; Insertion depth per side 40 mm; On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Flat trunking nipple connector made of galvanised sheet steel For direct connection of duct to duct Flat duct system for controlled domestic ventilation or extractor hoods 50 mm height Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1 Insertion depth per side 40 mm. On request: Special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Flat duct transition piece to spiral duct Pipe nipple to EN1506 with double lip seal for direct connection to spiral duct Duct nipple for direct insertion into flat duct system Material: galvanised steel The Intelmann flat duct system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Flat duct reduction Duct nipple on both sides for direct insertion into the flat duct system For connecting two pieces of flat trunking with different widths Material: Galvanised steel
Flat trunking T-piece b1 = width flat trunking; b2 = flat trunking outlet; height = 50 mm Plug-in flat duct system Flat duct system for controlled domestic ventilation or extractor hoods Material: galvanised steel The Intelmann flat duct system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Reinforcement for flat trunking for reinforcing flat trunking Universal size b=70mm, a=49mm, L=910mm for flat trunking from b=140mm.
Connection piece for disc valve / deflector / elbow Straight piece From flat duct to spiral duct Socket according to EN1506, z.b. For direct connection of a disc valve Material: galvanised steel, non-combustible to DIN 4102 class A1 Flat duct system for plugging
Connection piece for disc valve / deflector / elbow End piece From flat duct to spiral duct Socket according to EN1506, z.b. For direct connection of a disc valve Material: galvanised steel, non-combustible to DIN 4102 class A1 Flat duct system for plugging
Weather protection grille for flat duct Rear, angular connection for direct connection to flat duct With bird and fly screen Material: galvanised steel