Kellerentfeuchtung

Small room fan AKE 100 Cellar dehumidification, 92 m3/h, DN 100Features:Made in Germany quality, super quiet, fan connection DN 100, protection class IP X5 for safety in the cellar, protection class IIFor a better indoor climate in the cellar or laundry room, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldBarrier-free product, as it switches on/off automatically without an additional switch - low-maintenance device. Additional manual operation for 20 min. Automatic cellar dehumidification, frost and dry protection function. Uncomplicated one-man installation with standard tools. Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any utility room furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Design: Application range up to approx. 30 m2 per fan. Versatile expandability of the system: Connection of a supply air fan (z.B. ECA 11 E) possible to increase the air exchange. Fully automatic, intelligent cellar dehumidification for the highest demands. Permanent equalisation of the absolute humidity indoors and outdoors: fan ventilates independently if the absolute humidity in the room is higher than outside. No maintenance or manual control required: install once and the system works automatically. Additional fans without their own dew point control can be connected directly to the AKE up to max. 600 mA and benefit from the intelligence. Fans > 600 mA can be connected with an intermediate relay or contactor and thus also dehumidify larger or several rooms via the AKE. Concealed intake thanks to design cover. Barrier-free product, as it switches on/off automatically without additional switches. Fan monitors the room humidity. Frost protection function: system switches off at indoor temperatures below 5 °C. Dry protection function: Switches the system off at a relative humidity of less than 30 %. Additional manual operation for 20 min. can be switched on and off again via push-button. No additional installation from the switch to the device necessary. Additional manual continuous operation with switch possible. Status and function display via LEDs. Scope of delivery: Fan, external cover flap, sensors, 1 m connection cable, housing made of impact-resistant plastic. Thermal overload protection. Protection class II. Frost protection: To prevent the room from cooling down, the AKE has a frost protection function. The fan switches off automatically at indoor temperatures of less than 5 °C. Dry protection: To prevent the room from drying out, the AKE has a dry protection function. The fan switches off automatically at a relative room humidity of less than 30 %. Motor: Energy-saving, robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Simple installation: AKE 100: core hole drilling 105 mm, or 120 mm for installation with wall sleeve WH 100 accessory. AKE 150: core hole drilling 155 mm, or 170 mm for installation with wall sleeve WH 150. Wall and ceiling installation possible. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Surface-mounted installation for AKE 100 with accessory spacer frame ECA-DR.Artikel: AKE 100, delivery volume: 92 m3/h, speed: 2500 1/min, speed controllable: no, reversibility: no, SEC average: -24.18 kWh/(m2*a), voltage type: alternating current, rated voltage: 230 V, mains frequency: 50 Hz, rated power: 8 W, stand-by power consumption: 2 W, IMax: 0.06 A, protection class: IP X4, mains cable: 5 / 1.5 mm2, Installation location: wall, Installation type: surface-mounted, Installation position: any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.848 kg, Weight with packaging: 1.132 kg, Flap: none, Nominal width: 100 mm, Cable length: 1 m, Width: 159 mm, Height: 159 mm, Depth: 130 mm, Width with packaging: 225 mm, Height with packaging: 225 mm, Depth with packaging: 200 mm, Wall thickness: max. 0.85 m (if 1 m cable length is not sufficient, please also order the 6 m sensor cable), fluid temperature at IMax: 40 °C, sound pressure level: 32 dB(A) / distance 3 m, free-field conditions

Sensor cable 6m for AKE 100/150Features:Quality Made in GermanySensor cable - for a simple connectionFor AKE small room fans if standard cables are too short.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Optional sensor connection cable for AKE small room fans if the standard cable (1 m) is too short sollte.Artikel: Cable 6 m, Weight: 0.0394 kg, Weight with packaging: 0.047 kg, Length: 5 m, Width: 190 mm, Height: 100 mm, Depth: 150 mm, Width with packaging: 190 mm, Height with packaging: 15 mm, Depth with packaging: 150 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for residential ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

External grille SG 100 white, for aeration and ventilation, DN100Features:Quality Made in GermanyExternal grille - for easy installationWith concealed screw holes. Sealing tape included in the scope of delivery. External wall connection when using wall sleeve WH 100 & 120 & 150. Weather and UV-resistant plastic housingAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:External grille for ventilation. External wall connection when using wall sleeve WH100 & 120 & 150. SG 100 & 120 & 150/1: With concealed screw holes. Fly screen accessories FG 100 & 120 & 150 can be used. SG 100 B: brown. SG 15: With galvanised protective grille. Sealing tape included in the scope of delivery. Replacement air filter for SG 120: SF 120.Artikel: SG 100, Air direction: Ventilation, Installation: Outside, Installation location: Wall, Installation type: Surface-mounted, Material: Plastic, Weather-resistant, UV-resistant, Colour: Traffic white, similar to RAL 9016, Weight: 0.1 kg, Weight with packaging: 0.127 kg, Suitable for nominal width: 100 mm, Width: 150 mm, Height: 150 mm, Depth: 51.5 mm, Width with packaging: 151 mm, Height with packaging: 151 mm, Depth with packaging: 55 mm, Ambient temperature: 60 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no, With wire mesh: no, With insect screen: no, With pressure relief damper, intake: no, With pressure relief damper, exhaust: no, With counter-rotating damper valve: no, With co-rotating damper valve: no, With installation frame: no, Lockable: no, Motorised: no

Wall sleeve WH 150 plastic, extendable, DN150Features:Quality Made in GermanyWall sleeve - for easy installationFor wall and ceiling mounting. Variable length.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Wall sleeve for wall and ceiling mounting. Length variabel.Artikel: WH 150, Installation location: Wall / ceiling, Material: Plastic, Weight: 1.35 kg, Weight with packaging: 1.4 kg, Suitable for nominal diameter: 150 mm, Width: 168 mm, Height: 168 mm, Depth: 500 mm, Width with packaging: 168 mm, Height with packaging: 168 mm, Depth with packaging: 500 mm, Required core drilling: min. 169 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

FE 100/1 SG window installation kit with fixed outer flapFeatures:Made in Germany quality, super quietWindow installation kit - for easy installation in windows and thin wallsSimple installation thanks to interlocking adapters and threaded connectors. Electrical connection to the terminal strip in the housing. Scope of delivery: External flap AP or external grille SG, 3 x spacer frames, 2 x sealing rings, threaded connectors, 3 x screws for fan fastening, strain relief bracket with 2 x screws, cable sheath, installation instructionsAttractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation.Description:For installation in windows and thin walls. Colour traffic white similar to RAL 9016, housing made of impact-resistant plastic. Scope of delivery: External flap AP or external grille SG, 3 x spacer frames, 2 x sealing rings, threaded connectors, 3 x screws for fan fastening, strain relief bracket with 2 x screws, cable grommet, installation instructions. Installation instructions: Simple installation in the window cut-out thanks to interlocking adapter and threaded spigot. Pane thickness at least 3 mm, pane spacing up to 75 mm. Pane cut-out 115 to 120 mm. Not suitable for installation in hinged double windows. Electrical connection: To the terminal strip in the housing of the ECA 100 ipro...Article: FE 100/1 SG, Installation location: Window / thin wall, Installation position: Horizontal, Material: Plastic, impact-resistant, Colour: Traffic white, similar to RAL 9016, Weight: 0.4068 kg, Weight with packaging: 0.493 kg, Width: 150 mm, Height: 150 mm, Depth: 103 mm, Width with packaging: 158 mm, Height with packaging: 158 mm, Depth with packaging: 123 mm

AKE/1 - Brief informationControl unit AKE/1 incl. 2 pcs. AKE FFT humidity and temperature sensor (4m cable, can be extended on site to max. 30m) for fully automatic cellar dehumidification in conjunction with various fansAKE/1 - Product descriptionProduct featuresFully automatic, intelligent cellar dehumidification control for the highest demands.Permanent equalisation of the absolute humidity indoors and outdoors: Connected fans ventilate independently if the absolute humidity in the room is higher than outside.No maintenance or manual control required: install once and the system works automatically.Operation of fans up to a total (supply and extract air fan) of 600 W and 3 A.For the use of fans > 600 W and 3 A as well as three-phase fans, a circuit breaker must be installed between the control unit and the fan.Barrier-free product, as it switches on/off automatically without additional switches.Control unit monitors the room humidity via integrated humidity/temperature sensors.Frost protection function: system switches off at indoor temperatures below 5 °C.Additional manual operation for 30 minutes can be switched on and off again using a button on the control unit.No additional installation from the switch to the device necessary.Additional manual operation with external button or switch possible.Automatic button / switch detection.Status and function display via LEDs.Compact dimensions: Control unit 160 x 110 x 90 mm, outdoor sensor Ø50 mm, height 13 mm.Scope of delivery: Control unit, 2 sensors with 4 m cable length each.Sensor cable can be extended on site with LIYY 4x0.25 mm² cable to max. 30 (separate installation required).Housing made of impact-resistant plastic.IP protection: Control unit IP40 / outdoor sensor IP54.Frost protection: To prevent the room from cooling down, the AKE has a frost protection function. This automatically switches off the connected fan(s) at indoor temperatures of less than 5 °C.Garage dehumidification: optional switch-off of the frost protection function for unheated rooms.Suitable for continuous operation.Installation instructionsSimple installation: Wall mounting.Electrical connection: Surface-mounted.

ECA 11 E DN100 duct insertion fanFeatures:Made in Germany quality, super quiet, fan connection DN 100, protection class IP 45 for safety in the bathroom, protection class IIFor a better indoor climate in the bathroom or WC, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldInstallation of the fan in spiral ducts. Uncomplicated one-man installation with standard tools. Speed controllableAttractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Versions: ECA 11 E: Suitable for DN 100 pipes, with VDE-GS mark. Pipe insertion fan for installation in spiral ducts. For aeration or ventilation, depending on the installation position in the pipe. Housing made of impact-resistant plastic. Protection class II. Colour traffic white similar to RAL 9016. Protection against accidental contact in accordance with DIN EN ISO 13857 required, e.g. by means of protective grille SG and cover flap AP. Protective grille and automatic cover flap as accessories. Speed controllable, exception: ECA 15/2 E. Motor: Robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Thermal overload protection. Due to the phase control technology, a physically induced humming noise may occur in the lower speed range. Installation note: In dry rooms for any installation position geeignet.Artikel: ECA 11 E, delivery volume: 105 m3/h, speed: 2550 1/min, speed controllable: yes, reversibility: no, voltage type: alternating current, rated voltage: 230 V, mains frequency: 50 Hz / 60 Hz, power consumption: 13 W, IMax: 0.1 A, protection rating: IP 45, mains cable: 3 / 1.5 mm2, installation type: flush-mounted, installation position: Any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.514 kg, Weight with packaging: 0.586 kg, Nominal diameter: 100 mm, Width: 98 mm, Height: 98 mm, Depth: 109 mm, Width with packaging: 103 mm, Height with packaging: 103 mm, Depth with packaging: 125 mm, Conveying medium temperature at IMax: 40 °C, Sound pressure level: 37 dB(A) / distance 3 m, Free field conditions

Small room fan AKE 150 Cellar dehumidification, 250 m3/h, DN 150Features: Fully automatic, intelligent cellar dehumidification integrated in an exhaust air fan. Permanent equalisation of the absolute humidity indoors and outdoors: fan ventilates independently if the absolute humidity in the room is higher than outside.No maintenance or manual control required: install once and the system works automatically.Delivery volume up to 250 m³/h. Application range up to approx. 70 m² per fan.Concealed air intake thanks to design cover.Frost protection function: system switches off at indoor temperatures below 5 °C.Garage dehumidification: optional switch-off of the frost protection function for unheated rooms.Additional manual operation for 30 min. can be switched on and off again via push-button.Automatic button / switch detection.Status and function display via LEDs. Made in Germany quality, super quiet, fan connection DN 150, protection class IP X5 for safety in cellars, protection class IIFor a better indoor climate in the cellar or laundry room, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldBarrier-free product, as it switches on/off automatically without an additional switch - low-maintenance device. Additional manual operation for 20 min via button. Automatic cellar dehumidification, frost and dry protection function. Uncomplicated one-man installation with standard tools. Continuous operation possible via switch.Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any utility room furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Design: Application range up to approx. 70 m2 per fan. Versatile expandability of the system: Connection of a supply air fan (z.B. ECA 15/4 E) possible to increase the air exchange. Fully automatic, intelligent cellar dehumidification for the highest demands. Permanent equalisation of the absolute humidity indoors and outdoors: fan ventilates independently if the absolute humidity in the room is higher than outside. No maintenance or manual control required: install once and the system works automatically. Additional fans without their own dew point control can be connected directly to the AKE up to max. 600 mA and benefit from the intelligence. Fans > 600 mA can be connected with an intermediate relay or contactor and thus also dehumidify larger rooms or several rooms via the AKE. Concealed intake thanks to design cover. Barrier-free product, as it switches on/off automatically without additional switches. Fan monitors the room humidity. Frost protection function: system switches off at indoor temperatures below 5 °C. Dry protection function: Switches the system off at a relative humidity of less than 30 %. Additional manual operation for 20 min. can be switched on and off again using a button. No additional installation from the switch to the device necessary. Additional manual continuous operation with switch possible. Status and function display via LEDs. Scope of delivery: Fan, external cover flap, sensors, 1 m connection cable, housing made of impact-resistant plastic. Thermal overload protection. Protection class II. Frost protection: To prevent the room from cooling down, the AKE has a frost protection function. The fan switches off automatically at indoor temperatures of less than 5 °C. Dry protection: To prevent the room from drying out, the AKE has a dry protection function. The fan switches off automatically at a relative room humidity of less than 30 %. Motor: Energy-saving, robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Simple installation: AKE 100: core hole drilling 105 mm, or 120 mm for installation with wall sleeve WH 100 accessory. AKE 150: core hole drilling 155 mm, or 170 mm for installation with wall sleeve WH 150. Wall and ceiling installation possible. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Surface-mounted installation for AKE 100 with accessory spacer frame ECA-DR.Artikel: AKE 150, delivery volume: 250 m3/h, speed: 2189 1/min, speed controllable: no, reversibility: no, SEC average: -24.48 kWh/(m2*a), voltage type: alternating current, rated voltage: 230 V, mains frequency: 50 Hz, rated power: 19 W, stand-by power consumption: 2 W, IMax: 0.09 A, protection class: IP X4, mains cable: 5 / 1.5 mm2, Installation location: wall, Installation type: surface-mounted, Installation position: any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 1.8 kg, Weight with packaging: 2.37 kg, Flap: none, Nominal width: 150 mm, Cable length: 1 m, Width: 228 mm, Height: 228 mm, Depth: 178.3 mm, Width with packaging: 303 mm, Height with packaging: 273 mm, Depth with packaging: 303 mm, Wall thickness: max. 0.85 m (if 1 m cable length is not sufficient, please also order the 6 m sensor cable), fluid temperature at IMax: 40 °C, sound pressure level: 40 dB(A) / distance 3 m, free-field conditions

Wall sleeve WH 100 plastic, extendable, DN100Features:Quality Made in GermanyWall sleeve - for easy installationFor wall and ceiling mounting. Variable length.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Wall sleeve for wall and ceiling mounting. Variable length.Article: WH 100, Installation location: Wall / ceiling, Material: Plastic, Weight: 0.6 kg, Weight with packaging: 0.6 kg, Suitable for nominal diameter: 100 mm, Width: 114 mm, Height: 114 mm, Depth: 500 mm, Width with packaging: 114 mm, Height with packaging: 114 mm, Depth with packaging: 500 mm, Required core drilling: min. 115 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no