Isolierungen

Material: Elastomeric soft foam (FEF)Cell structure: closedColour: black / anthraciteMax. Temperature: +85°C Min. temperature: -50°C Thermal conductivity: 0.034 to 0.037Water vapour resistance: ≥10.000 µFire protection class: B-s3, d0Reaction to fire: Self-extinguishing, no dripping, no flame propagationHealth aspects: No bacterial and fungal growthSelf-adhesive insulation mats are typically used for thermal insulation in various applications. Their main purpose is to reduce heat loss or prevent heat transfer.Here are some typical applications and installation tips: Applications:1. building insulation: self-adhesive insulation mats can be applied to walls, ceilings and floors to reduce heat transfer between indoor and outdoor areas of a building. They help to reduce energy consumption and improve thermal comfort. 2. pipe insulation: These insulation mats can be wrapped around pipes to minimise heat loss and prevent pipes from freezing in cold environments. This is particularly important in heating and plumbing systems.3. vehicle insulation: Self-adhesive insulation mats can be used in vehicles to protect the interior from heat and cold. They help to improve driving comfort and can also help to reduce noise from outside. 4. industrial applications: In industrial facilities, these insulation mats are often used to protect equipment and facilities from extreme temperatures and increase energy efficiency.Installation:1. preparation: ensure that the surface to which the insulation mat will be applied is clean, dry and free from dirt, grease or other contaminants. 2. cutting: Cut the insulating mat to the required dimensions using a sharp knife or scissors. Make sure to allow enough material for overlaps or protrusions. 3. installation: Remove the protective film from the back of the insulating mat and press it firmly onto the surface to be insulated. Start in one corner and work evenly to avoid air bubbles and ensure good adhesion.4. sealing: If necessary, the overlaps of the insulation mats can be sealed with special adhesive tapes to ensure better insulation.5. finishing: Check the installed insulation mats for any gaps or irregularities and correct them if necessary. Ensure that all edges and connections are well sealed. With proper installation, self-adhesive insulation mats can effectively contribute to thermal insulation and reduce energy consumption in various applications.

Self-adhesive tape, 48 mm x 50 m / textile-reinforcedPVC adhesive tapesilver-grey

PE protective conduits 42 mm 1 1/4', 10 m/roll, redThin-wall conduit made of highly flexible, closed-cell soft polyethylenewith diffusion-tight outer skin and easy-to-install inner sliding filmApplication: up to +105°CFire class: B2, tested according to DIN 4102Insulation thickness: 4 mmColour: redLength: 10 m per loopFor cold water pipes in accordance with DIN 1988 Part 2

PE self-adhesive wrapping strip 70 x 2 mm, 3.6 mwith vapour barrierApplication: up to + 90 °CFire class: B2, tested according to DIN 4102Insulation thickness: 2 mmColour: red coatedLength: 3.6 m

PE drainage pipe insulation, DN 90, cast iron pipes (SML) 98, 10 m/roll, redWaste water insulation system for structure-borne noise insulationwith diffusion-tight outer skin and easy-to-install inner sliding foilApplication: up to +105°CFire class: B2, tested in accordance with DIN 4102Insulation thickness: 4 mmColour: redLength: 10 m per loopAs sound and condensation protection

Insulating strip/wrap felt self-adhesive 3.6 m with vapour barrierApplication: -70 to +105 °CFire class: B2, tested according to DIN 4102Insulation thickness: 2 mmLength: 3.6 mWidth: 70 mm

Insulating strip/wrap felt 3.6 m with vapour barrierApplication: -70 to +105 °CFire class: B2, tested according to DIN 4102Insulation thickness: 2 mmLength: 3.6 mWidth: 70 mm

Felt/fleece hose, DN 70, 10 m/rollThin-wall hose made of synthetic fibre fleecewith hard-wearing, water-impermeable PE film as outer skinApplication: -70 to +105°CFire class: B2, tested in accordance with DIN 4102Insulation thickness: 4 mmColour: whiteLength 10 m per loopFor cold water pipes in accordance with DIN 1988 Part 2