MONTAGEMATERIAL UND ZUBEHÖR

MEZ-PLAST 590 SMP, 300 ml cartridge, grey MEZ-PLAST 590 SMP is an elastic, fast-setting one-component sealant for HVAC applications, tested in accordance with DIN EN ISO 846.Application: Suitable for HVAC systems in accordance with VDI 6022 / EN 15780, as well as for grease exhaust air and clean rooms. With EC 1 Plus classification, MEZ-PLAST SMP fulfils the highest requirements for sustainable construction. Complies with DGNB 2018.Properties:Fungicidal and bactericidalNon-corrosiveQuickly tack-free surfaceFree from silicone and isocyanateVery low shrinkageGood weathering & ageing resistanceSolvent-freeSkin formation: Approx. 15 - 20 min.Curing: 3 - 4 mm on the 1st dayProcessing temperature: +5°C to +35°CTemperature resistance: -40°C to +90°CShelf life: 12 monthsREACH regulationSVHC ≤ 0.1 %MEZ-PLAST 590 SMP does not contain any substances of very high concern above 0.1%. PRODUCT HIGHLIGHTS: Low emission Silicone-free Free from solvents & isocyanateHigh temperature resistance

The connecting sleeve is used to connect a fan to a round air duct (spiral duct) with the same diameter. At the same time, it absorbs vibrations from the fan to the ventilation duct. The advantage of this type of connection is that the fan can be removed from the air duct system at any time for replacement or repair. The sleeve is made of galvanised sheet steel, fitted with a foam rubber seal with a thickness of 6 millimetres on the inside. There are two M6 screws at the ends of the adjusting ring for fixing the sleeve: screws and nuts are part of the product.

MEZ-PLAST 580, 310 ml cartridge, silver-grey Sealing compound for sealing air duct systems and technical installations without silicone an alternative to soldering very good adhesion to all metals Fast curing sealant High chemical resistance Product properties: good adhesion to greasy, oily substrates and all metals Permanently elastic resistant to ageing, weathering and UV radiation antibacterial and fungicidal (against fungal attack) toxicologically harmless Resistant to many chemicals fulfils the hygienic requirements for use in for use in clean rooms and the specifications of the VDI 6022 guideline. can be used on lightly oiled, corrosion-preserved metals without degreasing without silicone, without nitrogen CFC-free no AOX components no lead compounds no mercury compounds no chromium compounds MEZ-PLAST is lead- and chromate-free and therefore food-safe according to the law Technical data Raw material base: acrylic resin, solvent-curing Curing time: approx. 4 mm in the first 24 h at +23°C and 50% r.F. Temperature resistance: - 40°C to +80°C (permanent) - 40°C to +100°C max. 1 h Processing temperature: +2°C to +60°C Shore A hardness: 38 Density: 1.05 g/m3 Primer: no Skin formation time: 10 min. at 23°C and 50% r.F. Coating compatibility: yes, preliminary tests required Paintability: yes, preliminary tests required Shelf life: 12 months Storage: protect from frost Flash point: below +21°C /- 4°C Hazard class: A1 Area of application: Sticks and adheres to all metals for sealing in ventilation ducts and plant construction Bonding and sealing in clean rooms, chip production, etc. Notes: - MEZ-PLAST is ready to use and can be applied without pre-cleaning and degreasing the areas to be sealed using a brush, - spatula or spraying equipment. - can be painted over after curing - A slight shrinkage may occur due to evaporation of the solvents contained.

Duct clamp for pulling together air duct connection profiles For connecting rectangular air duct systems Suitable for all profile sizes incl. screwed-in screw M8 x 25 mm Material thickness 3 mm Material: galvanised steel The duct clamp is placed over the air duct profiles and fastened with the screw. The profiles are pressed against each other by tightening the clamp. Duct clamps should be installed so that the free length between 2 connection points does not exceed 200 mm. The hexagon head screw must be tightened to approx. 7 Nm.

The "Metal-Speed" plasterboard plugs / cavity plugs made of die-cast zinc enable simple and secure fastening in plasterboard. They are ideal for push-fit installation and can be installed without a special setting tool - a screwdriver or Phillips bit is all you need.Why metal speed plasterboard plugs?✅ Self-drilling - no pre-drilling required in single-layer plasterboard.✅ Quick and easy installation - Easy to use with a screwdriver or Phillips bit.✅ High load-bearing capacity - Form-fit fastening ensures a secure hold.✅ S uitable for various wall types - Ideal for plasterboard, limited for solid plasterboard and aerated concrete.✅ Compact dowel length - Also suitable for shallow cavity depths.✅ Fulfils fire protection requirements - Safe to use in various applications.Areas of application:Plasterboard walls & ceilings: Secure hold for screws, hooks and eyelets.Various substrates: Suitable for plasterboard, limited for solid plasterboard & aerated concrete.Residential & commercial areas: Universally applicable for various installation purposes.Technical details:✔ Material: Die-cast zinc✔ Installation: Push-fit installation without special tools✔ Pre-drilling: Not required in single layer plasterboard, Ø 8 mm in gypsum fibreboard and double planked plasterboard✔ Application: Suitable for commercially available hooks, screws and eyelets✔ S cope of delivery: 100 plasterboard plugs / cavity plugs "Metal-Speed"Thanks to their specially developed thread, the metal speed plasterboard plugs cut into the plasterboard with a positive fit and enable a wide variety of fastening elements to be installed quickly and securely.

The WTB fixing kit is the ideal solution for the professional installation of washbasins on the wall. The set contains all the necessary components for a stable and durable installation. The included galvanised hanger bolts (M10 x 120 mm orM10 x 140 mm) with matching hexagon nuts and washers ensure secure fastening. In addition, the eccentric collar sleeves supplied enable optimum adjustment of the washbasin. The all-purpose plugs ensure firm anchoring in various wall materials.Product details:Hanger bolts: 2 pieces, galvanisedHexagon nuts: 2 pieces, M10, galvanisedWashers: 2 pieces, suitable for M10Collar sleeves: 2 pieces, eccentric for height levellingPlugs: 2 pieces, all-purpose plugs for various wall typesWith the WTB fixing set, washbasin installation is quick, easy and secure. Perfect for DIY enthusiasts and professionals!

Installation rails / mounting rails Profile

Material: Elastomeric soft foam (FEF)Cell structure: closedColour: black / anthraciteMax. Temperature: +85°C Min. temperature: -50°C Thermal conductivity: 0.034 to 0.037Water vapour resistance: ≥10.000 µFire protection class: B-s3, d0Reaction to fire: Self-extinguishing, no dripping, no flame propagationHealth aspects: No bacterial and fungal growthSelf-adhesive insulation mats are typically used for thermal insulation in various applications. Their main purpose is to reduce heat loss or prevent heat transfer.Here are some typical applications and installation tips: Applications:1. building insulation: self-adhesive insulation mats can be applied to walls, ceilings and floors to reduce heat transfer between indoor and outdoor areas of a building. They help to reduce energy consumption and improve thermal comfort. 2. pipe insulation: These insulation mats can be wrapped around pipes to minimise heat loss and prevent pipes from freezing in cold environments. This is particularly important in heating and plumbing systems.3. vehicle insulation: Self-adhesive insulation mats can be used in vehicles to protect the interior from heat and cold. They help to improve driving comfort and can also help to reduce noise from outside. 4. industrial applications: In industrial facilities, these insulation mats are often used to protect equipment and facilities from extreme temperatures and increase energy efficiency.Installation:1. preparation: ensure that the surface to which the insulation mat will be applied is clean, dry and free from dirt, grease or other contaminants. 2. cutting: Cut the insulating mat to the required dimensions using a sharp knife or scissors. Make sure to allow enough material for overlaps or protrusions. 3. installation: Remove the protective film from the back of the insulating mat and press it firmly onto the surface to be insulated. Start in one corner and work evenly to avoid air bubbles and ensure good adhesion.4. sealing: If necessary, the overlaps of the insulation mats can be sealed with special adhesive tapes to ensure better insulation.5. finishing: Check the installed insulation mats for any gaps or irregularities and correct them if necessary. Ensure that all edges and connections are well sealed. With proper installation, self-adhesive insulation mats can effectively contribute to thermal insulation and reduce energy consumption in various applications.

Stainless steel pipe clampsApplicationFor fastening spiral ductsYour advantagesSuitable clamping ranges for all spiral ducts (standard)Catch lock: quick and easy insertion and fastening of the pipe thanks to the catch lock up to a nominal pipe diameter of 450 mm, from a nominal pipe diameter of 500 mm with M8 hexagon head screwEasy installation of the ventilation clamp thanks to the wide opening angle of the pipe clampStiffening of the ventilation clamp due to bead geometryEasy engagement of the screw plug with a fingertipHigh level of safety due to edge-locking suspension openingNo uncontrolled opening after engaging thanks to safety catch lockThe easy-to-engage lock allows the pipe clamp to be opened and closed with just one handWith highly elastic DÄMMGULAST® sound insulation insert: average sound level improvement of 18 dB(A)M8 threaded connections customised to the applicationThis product has been awarded the "pipe fastening quality mark" and is subject to external monitoring in accordance with RAL-GZ 655-B

Hanger bolts

Threaded rod, M24Steel, galvanisedaccording to DIN 975, strength 4.8Length: 1 m

Angle brackets, profile 38/40Dimension: 207 x 165 x 4Steel, galvanisedSturdy design, 90°Increases and reinforces the load-bearing capacity of trusses and rail constructions

WC fixings / galvanised steel 6.0 x 80, whiteSet complete with:2 hexagon head iron screws (with slot)2 dowels 8 mm2 plastic rosettes2 plastic cover caps

Adjusting tube brass, chrome-platedwith 3/4" hose fitting for appliance drain hoseDimension 32 x 200 mm

Universal valve with stainless steel strainer plateDimension 1 1/4" x 60 mmLower part brass, nickel-plated

Universal valve with plugDimension 1 1/4" x 60 mmLower part brass, nickel-platedStrainer plate chrome-nickel steel

Universal rails for radiators without brackets, 900 mmthe radiator is placed with the lower edge on the bracket, the upper bracket grips the radiator at the upper edge, the bracket is mounted under the decorative grilleSet complete with:2 brackets4 screws4 plugs

Stainless steel washers, DIN 9021, 8.4 mm for M 8Stainless steel A2DIN 9021 (wide washer)

Urinal fixings, 10 x 120, chromeSet complete with:2 galvanised hanger bolts2 nylon plugs2 plastic rosettes2 galvanised washers2 galvanised nuts2 plastic cover caps

Uni fastening set for radiators with welded-on brackets type D 1Complete set with:- 2 brackets- 2 spacers- 2 spanner screws 8 x 60 mm- 2 dowels 10 x 60 mm ✅ Complete set: Contains robust brackets, screws, plugs and spacers for quick, secure installation.✅ Universally applicable: Suitable for radiators with welded-on brackets type D 1 - ideal for living and working areas.✅ High stability: Durable materials ensure a firm hold, optimum load distribution and reliable corrosion protection.✅ Easy installation: All the necessary parts are included - simply attach, align and fix permanently.✅ Efficient heat dissipation: Precise wall clearance enables optimum air circulation and maximum heat output. The Uni fixing set for radiators with welded-on brackets type D 1 offers a reliable and stable solution for professional wall mounting of your radiators. The set contains all the necessary components - from solid brackets, robust screws and plugs to matching spacers - to ensure a secure and durable installation.This installation set can be used to professionally mount various radiator types in living rooms, offices or workshops. The high-quality metal brackets are designed for optimum load distribution so that your radiator sits firmly and securely on the wall. Thanks to the enclosed spacers, an exact distance from the wall is guaranteed, which supports efficient heat exchange and optimum air circulation.Advantages & areas of application:Versatile: Compatible with common radiator types with welded-on brackets (type D 1).Sturdy construction: High-quality materials ensure a durable, corrosion-resistant fixing.Easy installation: Complete accessory set with screws, plugs and spacers for easy installation on solid walls or masonry.Clean look: Ensures a professional mounting that blends harmoniously into any living or working area.Efficient heat output: Precisely adjusted wall distances ensure optimum air circulation and therefore effective heat distribution in the room.Regardless of whether you want to install a new radiator or replace an existing one: With this Uni fixing set for radiators, you are making a safe choice for a permanently stable fixing. Optimise your radiator installation now and benefit from a reliable, durable mounting system.

Beam clamps M8with VDS approvalwith M8 thread in the backClamping width 23Malleable cast ironwith 6 ct. screw and M10 lock nutfor suspension on steel beams and profiles without welding and drillingApproved for pipes up to 65 mm

Trapezoidal hanger with adjustable nut M8Steel, galvanisedThread: M 8Height: 120 mmMaterial thickness: 25 x 2.0 mmWith predetermined bending points to adapt to the various trapezoidal sheet metal profilesPermissible load 1.3 kNOne pre-assembled, captively secured adjusting nut for subsequent height correctionFastening to trapezoidal sheet metal using self-tapping screws, threaded rods or blind rivets

Rail connector, stable, profile 38/40Steel, galvanisedFor connecting mounting railsPre-assembled with 4 screws and spring washersUpper plate angled to stabilise the mounting railsScrew size M 10 x 20

Support brackets, profile 38/40, 800 mmGalvanised steelWelded support brackets for wall mounting of pipe traysprofile identical to the corresponding mounting railsMaterial thickness: 2.0 mm

Pin pipe clamps with sound insulation insert, 2 1/2 inch, 78 - 80 mmSteel, galvanisedDrive-in clamps with riveted square pinSound insulation for DIN4109Temperature resistance: -50°C to +110°CCaptive and screwdriver-friendly screw plugsPin length 80 mmMaterial dimensions: 20 x 2.0 mm

Sound insulation plug with collar, 18 x 70 mm, sound insulation 16.0 dBwith stop collarto avoid sound bridges during pipe installationSound insulation up to 16 dBScrew guide, no lateral break-out possibleSuitable for screws with wood threadMax. tensile load: 1.2 kN (applies to non-cracked concrete, strength class > B25 with max. screw diameter)

Stainless steel deck bolts

Screw pipe clamps with sound insulation insert, 95-103 mmwith 2 screw plugsSteel, galvanisedSound insulation for DIN 4109Temperature resistance -50°C to 110°CCaptive and screwdriver-friendly screw plugsConnection thread M8/M10Material thickness: 20 x 1.5mmWorking load 1.5 KN

Tinsmith screws (A2 - copper-plated) 4.5 x 45Stainless steel A2 (copper-plated)Screw size 4.5 x 45Screw with sealing disc (neoprene-coated) 19mmDrive T25