Flat trunking with internal reinforcement and fixing strip made of galvanised sheet steel, width 180 - 300 mm, height 50 mm. The width and height specifications refer to the internal dimensions of the trunking. The total length of the trunking is L=1000 mm. The flat duct is suitable for a wide range of applications. These range from supply and exhaust air ducts for controlled domestic ventilation to use as an exhaust air duct for an extractor bonnet in the kitchen and as a supply air duct for fireplaces or stoves. The duct is suitable for installation under the screed. The Intelmann flat duct system is designed according to the socket-nipple principle. This means that all moulded parts can be inserted into the ducts. Flat channels are connected to each other with nipples. Moulded parts, on the other hand, are connected to each other with a sleeve. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your pipework system. Flat duct system for controlled domestic ventilation or extractor hoods, 50 mm height. Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible to DIN 4102 class A1 Connection of duct and fitting with plug-in connection, sleeve and nipple. Insertion lengths generally 40 mm, all lengths without insertion lengths. Round connections to flat duct and spiral duct as well as spiral duct moulded parts with dimensions according to DIN EN 1506, all round nipples with EPDM double lip. On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium.
Flat trunking T-piece b1 = width flat trunking; b2 = flat trunking outlet; height = 50 mm Plug-in flat duct system Flat duct system for controlled domestic ventilation or extractor hoods Material: galvanised steel The Intelmann flat duct system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Flat duct socket connector for fittings made of galvanised sheet steel. For connecting moulded part to moulded part For connecting two pieces of moulding (bend with bend, bend with T-piece, etc.); NOT suitable for connecting flat duct to flat duct! Flat duct system for controlled domestic ventilation or extractor hoods; 50 mm height; Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1; Insertion depth per side 40 mm; On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Flat duct transition piece to spiral duct Pipe nipple to EN1506 with double lip seal for direct connection to spiral duct Duct nipple for direct insertion into flat duct system Material: galvanised steel The Intelmann flat duct system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.
Intelmann plastic air duct for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealants or solvents.Made of white plastic and temperature-resistant up to 60 °CFormat: 55х110 mm or 55x220 mmLength: 1000 mm
Intelmann plastic connector for connecting flat ducts (sleeve) Not suitable for connecting moulded parts (bends, T-piece, deflection piece), please use moulded part connector FKNK for this.Made of white plastic and temperature resistant up to 60° CSize: 55х110 mm or 55x220 mmType: Duct connector / sleeve
Intelmann plastic air duct bend 90° vertical for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealants or solvents.Made of white plastic and temperature resistant up to 60 °CFormat: 55х110 mm or 55x220 mmType: 90° vertical bend
Intelmann plastic air duct bend 90° flat to round for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealant or solvents.Made of white plastic and temperature resistant up to 60 °CFormat: 55х110 mm or 55x220 mmType: Bend 90° flat duct to round 100-125 mm
Intelmann plastic air duct T-piece for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealants or solvents.Made of white plastic and temperature resistant up to 60 °CFormat: 55х110 mm or 55x220 mmType: T-piece
Intelmann plastic connector for connecting moulded parts (nipples)For connecting: Bends, T-pieces, deflection pieces etc.Made of white plastic and temperature resistant up to 60 °CSize: 55х110 mm or 55x220 mmType: Moulded part connector / nipple
Intelmann plastic air duct bend 90° horizontal for the supply and exhaust air of rooms and extractor bonnets. The system is quick, easy and clean to install, without sealants or solvents.Made of white plastic and temperature resistant up to 60 °CFormat: 55х110 mm or 55x220 mmType: Horizontal 90° bend
Intelmann plastic flange for mounting flat ducts to a wall opening or similar.Made of white plastic and temperature resistant up to 60° CFormat: 55х110 mmType: FlangeMaterial: Plastic
MEZ-PLAST 580, 310 ml cartridge, silver-grey Sealing compound for sealing air duct systems and technical installations without silicone an alternative to soldering very good adhesion to all metals Fast curing sealant High chemical resistance Product properties: good adhesion to greasy, oily substrates and all metals Permanently elastic resistant to ageing, weathering and UV radiation antibacterial and fungicidal (against fungal attack) toxicologically harmless Resistant to many chemicals fulfils the hygienic requirements for use in for use in clean rooms and the specifications of the VDI 6022 guideline. can be used on lightly oiled, corrosion-preserved metals without degreasing without silicone, without nitrogen CFC-free no AOX components no lead compounds no mercury compounds no chromium compounds MEZ-PLAST is lead- and chromate-free and therefore food-safe according to the law Technical data Raw material base: acrylic resin, solvent-curing Curing time: approx. 4 mm in the first 24 h at +23°C and 50% r.F. Temperature resistance: - 40°C to +80°C (permanent) - 40°C to +100°C max. 1 h Processing temperature: +2°C to +60°C Shore A hardness: 38 Density: 1.05 g/m3 Primer: no Skin formation time: 10 min. at 23°C and 50% r.F. Coating compatibility: yes, preliminary tests required Paintability: yes, preliminary tests required Shelf life: 12 months Storage: protect from frost Flash point: below +21°C /- 4°C Hazard class: A1 Area of application: Sticks and adheres to all metals for sealing in ventilation ducts and plant construction Bonding and sealing in clean rooms, chip production, etc. Notes: - MEZ-PLAST is ready to use and can be applied without pre-cleaning and degreasing the areas to be sealed using a brush, - spatula or spraying equipment. - can be painted over after curing - A slight shrinkage may occur due to evaporation of the solvents contained.
Pre-laminating tape 4 mm x 12 mm Length: 10m / 20m Colour: Grey without firmly laminated silicone film Material: closed-cell polyethylene foam Self-adhesive on one side Temperature resistance: from - 30 to + 80 °C fulfils the hygienic requirements for use in air conditioning systems in accordance with VDI 6022 Reduction of noise transmission Motion damping Condensation water resistance: very good Versatile sealing and sealing tape/ suitable for a wide range of industrial and construction applications
Cold shrink tape is a self-vulcanising adhesive tape for indoor and outdoor use. The tape is extremely suitable for sealing round and rectangular air ducts. The tape can also be used to seal seams and cracks in gutters, skylight domes, etc.Butyl cold-shrink tape, aluminium-laminated W=50mm L=15m / roll Cold shrink tape made from butyl rubber with aluminium lamination; can be processed down to -20°C without preheating extreme strength and flexibility force-fit connection in the area of Aluflex and spiral ducts possible without screw connection Butyl cold shrink tape, aluminium-laminated Carrier: pure aluminium foil Carrier colour: silver/aluminium Butyl colour: grey Aluminium thickness: 0.04mm Butyl thickness: 0.80mm Total thickness: 0.84mm Cover: silicone paper Temperature resistance: -20°C to +80°C Dimension: 50mm/15m ApplicationFor indoor and outdoor use for air duct sealingExcellent weather resistanceIt can also be used for roof flashing and repair workInstantly provides a secure, watertight and airtight bond that becomes stronger over timeNo special skills requiredNo drying or heating is required