Small room fans

Small room fan AKE 100 Cellar dehumidification, 92 m3/h, DN 100Features:Made in Germany quality, super quiet, fan connection DN 100, protection class IP X5 for safety in the cellar, protection class IIFor a better indoor climate in the cellar or laundry room, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldBarrier-free product, as it switches on/off automatically without an additional switch - low-maintenance device. Additional manual operation for 20 min. Automatic cellar dehumidification, frost and dry protection function. Uncomplicated one-man installation with standard tools. Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any utility room furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Design: Application range up to approx. 30 m2 per fan. Versatile expandability of the system: Connection of a supply air fan (z.B. ECA 11 E) possible to increase the air exchange. Fully automatic, intelligent cellar dehumidification for the highest demands. Permanent equalisation of the absolute humidity indoors and outdoors: fan ventilates independently if the absolute humidity in the room is higher than outside. No maintenance or manual control required: install once and the system works automatically. Additional fans without their own dew point control can be connected directly to the AKE up to max. 600 mA and benefit from the intelligence. Fans > 600 mA can be connected with an intermediate relay or contactor and thus also dehumidify larger or several rooms via the AKE. Concealed intake thanks to design cover. Barrier-free product, as it switches on/off automatically without additional switches. Fan monitors the room humidity. Frost protection function: system switches off at indoor temperatures below 5 °C. Dry protection function: Switches the system off at a relative humidity of less than 30 %. Additional manual operation for 20 min. can be switched on and off again via push-button. No additional installation from the switch to the device necessary. Additional manual continuous operation with switch possible. Status and function display via LEDs. Scope of delivery: Fan, external cover flap, sensors, 1 m connection cable, housing made of impact-resistant plastic. Thermal overload protection. Protection class II. Frost protection: To prevent the room from cooling down, the AKE has a frost protection function. The fan switches off automatically at indoor temperatures of less than 5 °C. Dry protection: To prevent the room from drying out, the AKE has a dry protection function. The fan switches off automatically at a relative room humidity of less than 30 %. Motor: Energy-saving, robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Simple installation: AKE 100: core hole drilling 105 mm, or 120 mm for installation with wall sleeve WH 100 accessory. AKE 150: core hole drilling 155 mm, or 170 mm for installation with wall sleeve WH 150. Wall and ceiling installation possible. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Surface-mounted installation for AKE 100 with accessory spacer frame ECA-DR.Artikel: AKE 100, delivery volume: 92 m3/h, speed: 2500 1/min, speed controllable: no, reversibility: no, SEC average: -24.18 kWh/(m2*a), voltage type: alternating current, rated voltage: 230 V, mains frequency: 50 Hz, rated power: 8 W, stand-by power consumption: 2 W, IMax: 0.06 A, protection class: IP X4, mains cable: 5 / 1.5 mm2, Installation location: wall, Installation type: surface-mounted, Installation position: any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.848 kg, Weight with packaging: 1.132 kg, Flap: none, Nominal width: 100 mm, Cable length: 1 m, Width: 159 mm, Height: 159 mm, Depth: 130 mm, Width with packaging: 225 mm, Height with packaging: 225 mm, Depth with packaging: 200 mm, Wall thickness: max. 0.85 m (if 1 m cable length is not sufficient, please also order the 6 m sensor cable), fluid temperature at IMax: 40 °C, sound pressure level: 32 dB(A) / distance 3 m, free-field conditions

Small room fan ECA 100 ipro Standard, DN100Features:Quality Made in Germany, super quiet, two-stage fan connection DN 100, protection rating IP X5 for safety in the bathroom, protection class IIFor a better room climate in the bathroom or WC, the low-noise exhaust fan – the elegant solution against moisture, unpleasant odours and mouldVery easy operation by switching on and off with the light switch – low-maintenance device – straightforward one-person installation with standard tools. Continuous power connection required for run-on (4-core cable to the fan necessary)Attractive design with elegant front panel made of impact-resistant plastic – neutral white similar to RAL 9016, compatible with any bathroom furnishing style. Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Standard version: On/Off via light switch or separate switch. Operation either at stage 1 or stage 2. Two-stage operation possible using a standard double changeover switch. Speed controllable. Intelligently programmed small room fan for the highest demands. 2 power levels. Concealed intake through design cover. For ventilation. VDE-GS mark, exception: ECA 100 ipro RC/RCH. VDE mark: ECA 100 RC/RCH. Protection rating IP X5 for safety in the bathroom. Protection class II. Suitable for continuous operation. Thermal overload protection. Colour traffic white similar to RAL 9016. Housing made of impact-resistant plastic. Motor: energy-saving, robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Very easy installation as the cover can be easily removed with tools. Wall and ceiling mounting possible. Compatible with ECA predecessor models DN 100, as fixing holes and cable entry flush-mounted are in the same place. Electrical connection: Electrical connection flush-mounted. Safety instructions: All ECA 100 ipro devices can be used in protection zone 1 according to DIN VDE 0100-701. See planning notes for details. Article: ECA 100 ipro, version: standard version, air flow volume: 78 m3/h / 92 m3/h, speed: 2100 rpm / 2500 rpm, speed controllable: yes, reversibility: no, SEC average: -10.69 kWh/(m2*a), voltage type: alternating current, rated voltage: 230 V, mains frequency: 50 Hz, rated power: 6 W / 8 W, IMax: 0.06 A, protection rating: IP X5, power supply cable: 3/5 x 1.5 mm2, installation location: ceiling / wall, installation type: surface-mounted, installation position: any, material: plastic, colour: traffic white, similar to RAL 9016, weight: 0.7 kg, weight with packaging: 0.85 kg, flap: none, nominal diameter: 100 mm, width: 159 mm, height: 159 mm, depth: 130 mm, width with packaging: 165 mm, height with packaging: 165 mm, depth with packaging: 145 mm, medium temperature at IMax: 40 °C, sound pressure level: 27 dB(A) / 32 dB(A) / distance 3 m, free-field conditions

ECA 120 VZ - Brief InformationWith fixed inner grille and delay timer switchECA 120 VZ - Product DescriptionVersion with Delay Timer SwitchSwitch-on delay approx. 50 seconds.Run-on time approx. 6 minutes.Not speed controllable.FeaturesHigh air volume despite compact design.Combines large air volume with pressure strength.Thermal overload protection.Housing made of impact-resistant plastic.Protection class II.With VDE-GS mark, exception: ECA 120 24 V.With protective seals against the ingress of condensate when installed in ceilings.Speed control optional for ECA fans in standard version.Colour traffic white similar to RAL 9016.MotorRobust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsSimple, quick removal of the cover.Quick fastening of the fan in the duct by 2 clamping springs.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsECA 120 devices with protection class IP 45 can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring diagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation notes ArticleECA 120 VZVersionDelay timer switchAir volume170 m³/hSpeed2,600 rpmSpeed controllable−Reversibility−Type of currentAlternating currentRated voltage230 VMains frequency50 Hz / 60 HzPower consumption19 WIMax0.14 AProtection classIP 45Power cable5 x 1.5 mm²Installation locationWallType of installationSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight0.9 kgWeight with packaging1.06 kgNominal diameter120 mmWidth171 mmHeight171 mmDepth114 mmWidth with packaging180 mmHeight with packaging180 mmDepth with packaging140 mmMedium temperature at IMax40 °CRun-on time6 minSwitch-on delay50 sSound pressure level42 dB(A) / Distance 3 m, free field conditions

Small room fan ECA piano H humidity control, DN100Features:Made in Germany quality, super quiet, fan connection DN 100, protection class IP X4 for safety in the bathroom, protection class IIFor a better indoor climate in the bathroom or WC, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldBarrier-free product, as it switches on/off automatically via humidity sensor - low-maintenance device. Fan monitors room humidity and vents automatically. Uncomplicated one-man installation with standard tools. Permanent power connection required for adjustable run-on time (4-core cable to fan). Not speed controllable Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Humidity control version with adjustable overrun: Barrier-free product, as it switches on / off automatically. With VDE mark. Switch-on humidity adjustable from approx. 50 % relative humidity to approx. 90 % relative humidity. Can be switched on manually with an additional switch, fan then runs for the set run-on time. Run-on time adjustable from approx. 0.5 min to approx. 18 min. Humidity control has priority. Not speed-controllable. Particularly quiet thanks to innovative piano impeller. Cover can be removed for cleaning without tools. Compatible with ECA 100 ipro and ECA predecessor models DN 100, same position of screw holes and cable entry. Protection class IP X4 for safety in the bathroom. Protection class II. Integrated springless non-return flap, durable and stable. Colour traffic white similar to RAL 9016. Suitable for DN 100 pipe. Housing made of impact-resistant plastic. Thermal overload protection. Motor: Robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Extremely simple installation as cover can be removed without tools. Wall and ceiling mounting possible, hole in cover required for ceiling mounting. Electrical connection: Flush-mounted electrical connection. Safety instructions: All ECA piano devices can be used in protection zone 2 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA piano H, Version: Humidity control with adjustable overrun, Delivery volume: 80 m3/h, Speed: 2400 1/min, Speed controllable: no, Reversibility: no, Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Rated power: 8 W, IMax: 0.06 A, Protection rating: IP X4, Mains cable: 3/5 x 1.5 mm2, Installation location: Wall / ceiling, Installation type: Surface-mounted, Installation position: Any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.5 kg, Weight with packaging: 0.63 kg, Nominal width: 100 mm, Width: 151 mm, Height: 151 mm, Depth: 104 mm, Width with packaging: 160 mm, Height with packaging: 160 mm, Depth with packaging: 130 mm, Conveying medium temperature at IMax: 40 °C, Run-on time: 0.5 min - 18 min - Run-on time when using an optional switch (z.B. Light switch) available, sound pressure level: 26 dB(A) / distance 3 m, free field conditions

ECA 120 K small room fan internal shutter, standard, DN120Features:Made in Germany quality, Super quiet, Fan fastening with 2 clamping springs in the pipeFor a better indoor climate in the bathroom or WC, The low-noise exhaust air fan - the elegant solution against humidity, unpleasant odours and mouldSimple operation by switching on/off with the light switch - low-maintenance device. Uncomplicated one-man installation with standard tools. Speed controllable. With electrically operated internal lock and protective seals to prevent the ingress of condensation water Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Standard version: With electrically operated internal lock. Speed controllable. Exception: ECA 150/4 K. Due to the phase control technology, a physically induced humming noise can occur in the lower speed range. High delivery volume despite compact size. Combines high delivery volume with high pressure. Thermal overload protection. Housing made of impact-resistant plastic. Protection class II. With VDE-GS mark, exception: ECA 120 24 V. With protective seals to prevent the ingress of condensation water when installed in ceilings. Speed control optional for ECA fans in standard version. Colour traffic white similar to RAL 9016. Motor: Robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Simple, quick removal of the cover. Quick fastening of the fan in the duct using 2 clamping springs. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Safety instructions: ECA 120 devices with protection class IP 45 can be used in protection zone 1 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA 120 K, Version: Standard version, Delivery volume: 180 m3/h, Speed: 2600 1/min, Speed controllable: yes, Reversible: no, Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Power consumption: 19 W, IMax: 0.14 A, Protection rating: IP 34, Mains cable: 3 / 1.5 mm2, Installation location: Wall, Installation type: Surface-mounted, Installation position: Any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.9 kg, Weight with packaging: 1.08 kg, Damper type: electric, Nominal width: 120 mm, Width: 171 mm, Height: 171 mm, Depth: 114 mm, Width with packaging: 180 mm, Height with packaging: 180 mm, Depth with packaging: 140 mm, Fluid temperature at IMax: 40 °C, Sound pressure level: 36 dB(A) / distance 3 m, Free field conditions

ECA 120 KVZ - Brief InformationWith electric internal lock and delay timer switchECA 120 KVZ - Product DescriptionVersion with Delay Timer SwitchWith electrically operated internal lock.Switch-on delay approx. 50 seconds.Run-on time approx. 6 minutes.Not speed controllable.FeaturesHigh air volume despite compact design.Combines large air volume with pressure strength.Thermal overload protection.Housing made of impact-resistant plastic.Protection class II.With VDE-GS mark, exception: ECA 120 24 V.With protective seals against the ingress of condensate when ceiling mounted.Speed control optional for ECA fans in standard version.Colour traffic white similar to RAL 9016.MotorRobust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsSimple, quick removal of the cover.Quick fastening of the fan in the duct by 2 clamping springs.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsECA 120 devices with protection class IP 45 can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring DiagramsSafety instructions for small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation Instructions ArticleECA 120 KVZVersionDelay timer switchAir volume180 m³/hSpeed2,600 1/minSpeed controllable−Reversibility−Type of voltageAlternating currentRated voltage230 VMains frequency50 Hz / 60 HzPower consumption19 WIMax0.14 AProtection classIP 34Power cable5 x 1.5 mm²Installation locationWallType of installationSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight0.9 kgWeight with packaging1.06 kgType of flapElectricNominal size120 mmWidth171 mmHeight171 mmDepth114 mmWidth with packaging180 mmHeight with packaging180 mmDepth with packaging140 mmMedium temperature at IMax40 °CRun-on time6 minSwitch-on delay50 sSound pressure level36 dB(A) / Distance 3 m, free field conditions

Small room fan ECA 120 24 V safety extra-low voltage, DN120Features:Made in Germany quality, super quiet, fan fastening with 2 clamping springs in the pipe, protection class IP 45 for safety in the bathroom, protection class IIFor a better indoor climate in the bathroom or WC, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldOn/off switch via electrical connection, optionally surface-mounted or flush-mounted - low-maintenance device. Use only with approved safety transformer. Uncomplicated one-man installation with standard tools. Protective seal against condensation.Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Version with safety extra-low voltage: Rated voltage 24 V, 50 Hz. Use only with approved safety transformer (on site, 230 V/24 V). Combination with delay timer VZ 6, VZ 12 or VZ 24 C (see accessories) possible. Install the delay timers between the switch (230 V) and the input side of the safety transformer. Not speed-controllable. High delivery volume despite compact size. Combines high delivery volume with pressure strength. Thermal overload protection. Housing made of impact-resistant plastic. Protection class II. With VDE-GS mark, exception: ECA 120 24 V. With protective seals to prevent the ingress of condensation water when installed in ceilings. Speed control optional for ECA fans in standard version. Colour traffic white similar to RAL 9016. Motor: Robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Simple, quick removal of the cover. Quick fastening of the fan in the duct using 2 clamping springs. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Safety instructions: ECA 120 devices with protection class IP 45 can be used in protection zone 1 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA 120 24 V, Version: Safety extra-low voltage, Delivery volume: 170 m3/h, Speed: 2600 1/min, Speed controllable: no, Reversibility: no, Voltage type: Alternating current, Rated voltage: 24 V, Mains frequency: 50 Hz / 60 Hz, Power consumption: 19 W, IMax: 1.2 A, Protection rating: IP 45, Mains cable: 3 / 1.5 mm2, Installation location: Wall, Installation type: Surface-mounted, Installation position: Any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.9 kg, Weight with packaging: 1.06 kg, Nominal diameter: 120 mm, Width: 171 mm, Height: 171 mm, Depth: 114 mm, Width with packaging: 180 mm, Height with packaging: 180 mm, Depth with packaging: 140 mm, Fluid temperature at IMax: 40 °C, Sound pressure level: 42 dB(A) / distance 3 m, Free-field conditions

ECA 120 KF small room fan internal shutter, light, DN120Features:Made in Germany quality, Super quiet, Fan fastening with 2 clamping springs in the pipeFor a better indoor climate in the bathroom or WC, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldBarrier-free product, as it switches on/off automatically via light control - low-maintenance device. Uncomplicated one-man installation with standard tools. Continuous power connection required for adjustable run-on time (4-core cable to fan). Not speed-controllable. Protective seals against condensationAttractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Version with light control: With electrically operated inner lock. Barrier-free product, as it switches on and off automatically. The light control switches the fan on from a minimum brightness in the room, e.g. when a lamp is switched on. Switch-on brightness (on the device) min. 30 lux. Switch-off brightness (on the device) max. 0.3 lux. No need to install a switch. Switch-on delay approx. 50 seconds. Run-on time approx. 6 minutes. Not speed-controllable. High delivery volume despite compact size. Combines high delivery volume with high pressure. Thermal overload protection. Housing made of impact-resistant plastic. Protection class II. With VDE-GS mark, exception: ECA 120 24 V. With protective seals to prevent the ingress of condensation water when installed in ceilings. Speed control optional for ECA fans in standard version. Colour traffic white similar to RAL 9016. Motor: Robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Simple, quick removal of the cover. Quick fastening of the fan in the duct using 2 clamping springs. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Safety instructions: ECA 120 devices with protection class IP 45 can be used in protection zone 1 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA 120 KF, Version: Light control, Delivery volume: 180 m3/h, Speed: 2600 1/min, Speed controllable: no, Reversibility: no, Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Power consumption: 19 W, IMax: 0.14 A, Protection rating: IP 34, Mains cable: 3 / 1.5 mm2, Installation location: Wall, Installation type: Surface-mounted, Installation position: Any, Material: Plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.9 kg, Weight with packaging: 1.06 kg, Damper type: electric, Nominal width: 120 mm, Width: 171 mm, Height: 171 mm, Depth: 114 mm, Width with packaging: 180 mm, Height with packaging: 180 mm, Depth with packaging: 140 mm, Conveying medium temperature at IMax: 40 °C, Run-on time: 6 min, Switch-on delay: 50 s, Sound pressure level: 36 dB(A) / distance 3 m, Free-field conditions

ECA 120 F small room fan with internal grille and light, DN120Features:Made in Germany quality, super quiet, fan fastening with 2 clamping springs in the pipe, protection class IP 45 for safety in the bathroom, protection class IIFor a better indoor climate in the bathroom or WC, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldBarrier-free product as it switches on/off automatically via minimum brightness in the room - low-maintenance device. Uncomplicated one-man installation with standard tools. Switch-on delay and run-on time. No rotary switch control and with fixed inner grille. Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Version with light control: Barrier-free product, as automatic switching on/off is possible via the light control. The light control switches the fan on from a minimum brightness in the room, e.g. when a lamp is switched on. Switch-on brightness (on the device) min. 30 lux. Switch-off brightness (on the device) max. 0.3 lux. No need to install a switch. Switch-on delay approx. 50 sec. Switching variant: With an additional switch, the fan can be switched off independently of the room lighting (see wiring diagrams on the Internet). Not speed-controllable. High delivery volume despite compact size. Combines high delivery volume with high pressure. Thermal overload protection. Housing made of impact-resistant plastic. Protection class II. With VDE-GS mark, exception: ECA 120 24 V. With protective seals to prevent the ingress of condensation water when installed in ceilings. Speed control optional for ECA fans in standard version. Colour traffic white similar to RAL 9016. Motor: Robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Simple, quick removal of the cover. Quick fastening of the fan in the duct using 2 clamping springs. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Safety instructions: ECA 120 devices with protection class IP 45 can be used in protection zone 1 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA 120 F, Version: Light control, Delivery volume: 170 m3/h, Speed: 2600 1/min, Speed controllable: no, Reversible: no, Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Power consumption: 19 W, IMax: 0.14 A, Protection rating: IP 45, Mains cable: 3 / 1.5 mm2, Installation location: Wall, Installation type: Surface-mounted, Installation position: Any, Material: Plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.9 kg, Weight with packaging: 1.065 kg, Nominal width: 120 mm, Width: 171 mm, Height: 171 mm, Depth: 114 mm, Width with packaging: 180 mm, Height with packaging: 180 mm, Depth with packaging: 140 mm, Fluid temperature at IMax: 40 °C, Run-on time: 6 min, Switch-on delay: 50 s, Sound pressure level: 42 dB(A) / distance 3 m, Free-field conditions

ECA 120 KP - Brief InformationWith electric internal lock and pull cord switchECA 120 KP - Product DescriptionVersion with Pull Cord SwitchWith electrically operated internal lock.With pull cord switch and pull cord.Not speed controllable.FeaturesHigh air volume despite compact design.Combines large air volume with pressure strength.Thermal overload protection.Housing made of impact-resistant plastic.Protection class II.With VDE-GS mark, exception: ECA 120 24 V.With protective seals against the ingress of condensate water when installed in ceilings.Speed control optional for ECA fans in standard version.Colour traffic white similar to RAL 9016.MotorRobust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsSimple, quick removal of the cover.Quick fastening of the fan in the duct by 2 clamping springs.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsECA 120 devices with protection class IP 45 can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.

Small room fan ECA 150 ipro standard version, DN150Features:Quality Made in Germany, Super quiet, two-stage fan connection DN 150, Protection class IP X5 for safety in the kitchen, Protection class IIFor a better indoor climate in the kitchen or cellar, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldSimple operation by switching on/off with the light switch - low-maintenance device - uncomplicated one-man installation with standard tools. Permanent power connection required for run-on time (4-core cable to fan required) Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any kitchen furnishing styleSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Standard version: On/off via light switch or separate switch. Operation in either level 1 or level 2. Can be operated in two stages using a standard double changeover switch. Speed controllable. Intelligently programmed small room fan for the highest demands. 2 performance levels. Concealed intake through design cover. For ventilation. Combines high flow volume with high pressure. With VDE-GS mark. Protection class IP X5 for safety in the bathroom. Protection class II. Thermal overload protection. Suitable for continuous operation. Colour traffic white similar to RAL 9016. Housing made of impact-resistant plastic. Motor: Energy-saving, robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Compatible with ECA predecessor models DN 150, as the fixing holes and flush-mounted cable entry are in the same place. Wall and ceiling mounting possible. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Safety instructions: All ECA 150 ipro devices can be used in protection zone 1 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA 150 ipro, Version: Standard version, Delivery volume: 200 m3/h / 250 m3/h, Speed: 1672 1/min / 2189 1/min, Speed controllable: yes, Reversible: no, SEC average: -11.18 kWh/(m2*a), Voltage type: alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz, Rated power: 15 W / 19 W, IMax: 0.09 A, Protection rating: IP X5, Mains cable: 5 / 1.5 mm2, Installation location: ceiling / wall, Installation type: Surface-mounted, Installation position: Any, Material: Plastic, Colour: Traffic white, similar to RAL 9016, Weight: 1.6 kg, Weight with packaging: 1.885 kg, Flap: None, Nominal width: 150 mm, Width: 228 mm, Height: 228 mm, Depth: 123.3 mm, Width with packaging: 235 mm, Height with packaging: 235 mm, Depth with packaging: 200 mm, Fluid temperature at IMax: 40 °C, Sound pressure level: 33 dB(A) / 40 dB(A) / distance 3 m, Free field conditions

ECA 150 ipro K - Brief InformationTwo-stage small room fan, DN 150, with electric internal damperECA 150 ipro K - Product DescriptionStandard VersionOn/Off via light switch or separate switch.Operation either at stage 1 or stage 2.Two-stage operation using a standard double two-way switch.Speed controllable.Concealed intake with electrically operated internal damper.FeaturesIntelligently programmed small room fan for highest demands.2 power levels.Concealed intake through design cover.For ventilation.Combines large volume flow with high pressure strength.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Thermal overload protection.Suitable for continuous operation.Colour traffic white similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with maintenance-free ball bearings.Suitable for continuous operation.Installation InstructionsCompatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same place.Wall and ceiling mounting possible.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsAll ECA 150 ipro devices can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring DiagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation Notes ArticleECA 150 ipro KVersionStandard versionVolume flow200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable✔Reversibility−SEC average-10.49 kWh/(m²*a)Type of voltageAlternating currentRated voltage230 VMains frequency50 HzRated power18 W / 22 WIMax0.11 AProtection classIP X5Power cable3/5 x 1.5 mm²Installation locationCeiling / WallType of installationSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.7 kgWeight with packaging1.96 kgDamperIntegratedType of damperElectricNominal diameter150 mmWidth228 mmHeight228 mmDepth123.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CSound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free field conditions

ECA 150 ipro VZC - Brief InformationTwo-stage small room fan, DN 150, with adjustable switch-on delay and run-on timeECA 150 ipro VZC - Product DescriptionVersion with adjustable switch-on delay and run-on timeOn/Off via light switch or separate switch.All 4 operating programmes selectable.Sequence of power levels depends on selected operating programme.Switch-on delay adjustable in steps via easily accessible buttons: 0/50/90/120 sec.Run-on time adjustable in steps via easily accessible buttons: 0/8/17/25 min.Set time is displayed by LEDs during adjustment.Not speed controllable.Operating ProgrammesAdjustable via jumper in the device.Comfort programme (preset)User present: Level 1Run-on time: Level 2Demand programmeUser present: Level 2Run-on time: Level 1Economy programmeUser present: Level 1Run-on time: Level 1Power programmeUser present: Level 2Run-on time: Level 2FeaturesIntelligently programmed small room fan for highest demands.2 power levels.Concealed intake through design cover.For exhaust ventilation.Combines large air volume with high pressure strength.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Thermal overload protection.Suitable for continuous operation.Colour traffic white similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with maintenance-free ball bearings.Suitable for continuous operation.Installation InstructionsCompatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same place.Wall and ceiling mounting possible.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsAll ECA 150 ipro devices can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring diagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation notes ArticleECA 150 ipro VZCVersionAdjustable switch-on delay and run-on timeAir volume200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-11.04 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power15 W / 19 WIMax0.09 AProtection classIP X5Power cable5 x 1.5 mm²Installation locationCeiling / WallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.6 kgWeight with packaging1.9 kgFlapNoneNominal diameter150 mmWidth228 mmHeight228 mmDepth123.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CRun-on time0 min / 8 min / 17 min / 25 minSwitch-on delay0 s / 50 s / 90 s / 120 sSound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free-field conditions

ECA 150 ipro H - Brief InformationTwo-stage small room fan, DN 150, with humidity controlECA 150 ipro H - Product DescriptionVersion with automatic humidity controlBarrier-free product, as automatic switching on/off via humidity sensor.No setting of switch-on humidity necessary. Fan monitors the room humidity.Automatically ventilates depending on room humidity in stage 1 or stage 2.Operation without switch possible, optionally also switchable via separate switch.Switch-on delay adjustable in steps via easily accessible buttons (only with control via switch): 0/50/90/120 sec.Run-on time adjustable in steps via easily accessible buttons: 8/17/25 min. Run-on time 0 min only adjustable with control via separate switch.Set time is displayed by LEDs during adjustment.Not speed controllable.Operating ProgramsAdjustable via jumper in the device.Comfort program (preset)User present: Stage 1Run-on time: Stage 2Demand programUser present: Stage 2Run-on time: Stage 1Economy programUser present: Stage 1Run-on time: Stage 1Power programUser present: Stage 2Run-on time: Stage 2FeaturesIntelligently programmed small room fan for highest demands.2 power stages.Concealed intake through design cover.For ventilation.Combines large volume flow with high pressure strength.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Thermal overload protection.Suitable for continuous operation.Colour traffic white similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with maintenance-free ball bearings.Suitable for continuous operation.Installation InstructionsCompatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same place.Wall and ceiling mounting possible.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsAll ECA 150 ipro devices can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring diagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation notes ArticleECA 150 ipro HVersionHumidity controlVolume flow200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-24.48 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power15 W / 19 WIMax0.09 AProtection classIP X5Power cable3/5 x 1.5 mm²Installation locationCeiling / WallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.6 kgWeight with packaging1.91 kgFlapNoneNominal diameter150 mmWidth228 mmHeight228 mmDepth123.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CRun-on time8 min / 17 min / 25 min / Run-on time 0 min available when using an optional switch (e.g. light switch)Switch-on delay0 s / 50 s / 90 s / 120 s / Switch-on delay available when using an optional switch (e.g. light switch)Sound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free-field conditions

ECA 150 ipro KVZC - Short InformationTwo-stage small room fan, DN 150, with electric internal damper and adjustable switch-on delay and run-on timeECA 150 ipro KVZC - Product DescriptionVersion with adjustable switch-on delay and run-on timeOn/Off via light switch or separate switch.All 4 operating programmes selectable.Sequence of power levels depends on selected operating programme.Switch-on delay adjustable in steps via easily accessible buttons: 0/50/90/120 sec.Run-on time adjustable in steps via easily accessible buttons: 0/8/17/25 min.Set time is displayed by LEDs during adjustment.Concealed intake with electrically operated internal damper.Not speed controllable.Operating ProgrammesAdjustable via jumper in the device.Comfort programme (preset)User present: Level 1Run-on time: Level 2Demand programmeUser present: Level 2Run-on time: Level 1Economy programmeUser present: Level 1Run-on time: Level 1Power programmeUser present: Level 2Run-on time: Level 2FeaturesIntelligently programmed small room fan for highest demands.2 power levels.Concealed intake through design cover.For ventilation.Combines large volume flow with high pressure strength.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Thermal overload protection.Suitable for continuous operation.Traffic white colour similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with maintenance-free ball bearings.Suitable for continuous operation.Installation InstructionsCompatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same place.Wall and ceiling mounting possible.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsAll ECA 150 ipro devices can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring diagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation notes ArticleECA 150 ipro KVZCVersionAdjustable switch-on delay and run-on timeVolume flow200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-10.31 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power18 W / 22 WIMax0.11 AProtection classIP X5Power cable5 x 1.5 mm²Installation locationCeiling / WallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.7 kgWeight with packaging1.97 kgDamperIntegratedType of damperElectricNominal diameter150 mmWidth228 mmHeight228 mmDepth123.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmMedium temperature at IMax40 °CRun-on time0 min / 8 min / 17 min / 25 minSwitch-on delay0 s / 50 s / 90 s / 120 sSound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free field conditions

Small room fan ECA 150 ipro KB internal shutter, movement, DN150Features:Made in Germany quality, Super quiet, two-stage fan connection DN 150, Protection class IP X5 for safety in the kitchen, Protection class IIFor a better indoor climate in the bathroom or WC, The low-noise exhaust fan - the elegant solution against moisture, unpleasant odours and mouldBarrier-free product, as it switches on/off automatically via motion sensor or optionally via switch and electronic internal lock. Uncomplicated one-man installation with standard tools. Permanent power connection required for overrun (4-core cable to fan required)Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Version with motion detector: Barrier-free product, as automatic switch-on / switch-off via motion sensor. All 4 operating programmes selectable. The sequence of power levels depends on the selected operating programme. Operation without switch possible, can also be switched via separate switch as an option. No switch-on delay. Run-on time can be set in stages using easily accessible buttons: 0/8/17/25 min. Set time is indicated by LEDs during setting. Range of the motion detector: 5 m. Horizontal detection range of the motion detector: 100°. Vertical detection range of the motion detector: 82°. Concealed suction, with electrically operated internal shutter. Not speed-controllable. Operating programmes, adjustable via jumper in the device. Comfort programme (preset), user present: level 1, run-on time: level 2, demand programme, user present: level 2, run-on time: level 1, economy programme, user present: level 1, run-on time: level 1, power programme, user present: level 2, run-on time: level 2, intelligently programmed small room fan for the highest demands. 2 performance levels. Concealed intake through design cover. For ventilation. Combines high flow rate with high pressure. With VDE-GS mark. Protection class IP X5 for safety in the bathroom. Protection class II. Thermal overload protection. Suitable for continuous operation. Colour traffic white similar to RAL 9016. Housing made of impact-resistant plastic. Motor: Energy-saving, robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Compatible with ECA predecessor models DN 150, as the fixing holes and flush-mounted cable entry are in the same place. Wall and ceiling mounting possible. Electrical connection: Electrical connection optionally surface-mounted or flush-mounted. Safety instructions: All ECA 150 ipro devices can be used in protection zone 1 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA 150 ipro KB, Version: Motion detector, Delivery volume: 200 m3/h / 250 m3/h, Speed: 1672 1/min / 2189 1/min, Speed controllable: no, Reversible: no, SEC average: -24.05 kWh/(m2*a), Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz, Rated power: 18 W / 22 W, IMax: 0.11 A, Protection rating: IP X5, Mains cable: 3 / 1.5 mm2, Installation location: Ceiling / wall, Installation type: Surface-mounted, Installation position: Any, Material: Plastic, Colour: traffic white, similar to RAL 9016, Weight: 1.5 kg, Weight with packaging: 1.77 kg, Flap: integrated, Flap type: electric, Nominal width: 150 mm, Width: 228 mm, Height: 228 mm, Depth: 123.3 mm, Width with packaging: 235 mm, height with packaging: 235 mm, depth with packaging: 200 mm, fluid temperature at IMax: 40 °C, run-on time: 0 min / 8 min / 17 min / 25 min, sound pressure level: 33 dB(A) / 40 dB(A) / distance 3 m, free-field conditions

ECA 150 ipro B - Brief InformationTwo-stage small room fan, DN 150, with motion detectorECA 150 ipro B - Product DescriptionVersion with Motion DetectorBarrier-free product due to automatic switching on/off via motion sensor.All 4 operating programmes selectable.Sequence of power levels depends on selected operating programme.Operation without switch possible, optionally also switchable via separate switch.No switch-on delay.Run-on time adjustable in steps via easily accessible button: 0/8/17/25 min.Set time is displayed by LEDs during adjustment.Range of motion detector: 5 m.Horizontal detection angle of motion detector: 100°.Vertical detection angle of motion detector: 82°.Not speed controllable.Operating ProgrammesAdjustable via jumper inside the device.Comfort programme (preset)User present: Level 1Run-on time: Level 2Demand programmeUser present: Level 2Run-on time: Level 1Economy programmeUser present: Level 1Run-on time: Level 1Power programmeUser present: Level 2Run-on time: Level 2FeaturesIntelligently programmed small room fan for highest demands.2 power levels.Concealed intake through design cover.For exhaust ventilation.Combines large air volume with high pressure strength.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Thermal overload protection.Suitable for continuous operation.Colour traffic white similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with maintenance-free ball bearings.Suitable for continuous operation.Installation InstructionsCompatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same position.Wall and ceiling mounting possible.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsAll ECA 150 ipro devices can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring DiagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation Notes ArticleECA 150 ipro BVersionMotion detectorAir volume200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-24.48 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power15 W / 19 WIMax0.09 AProtection classIP X5Power cable3/5 x 1.5 mm²Installation locationCeiling / WallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.6 kgWeight with packaging1.91 kgFlapNoneNominal diameter150 mmWidth228 mmHeight228 mmDepth123.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CRun-on time0 min / 8 min / 17 min / 25 minSound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free-field conditions

ECA 150 ipro KH - Brief InformationTwo-stage small room fan, DN 150, with electric internal damper and humidity controlECA 150 ipro KH - Product DescriptionVersion with Automatic Humidity ControlBarrier-free product, as automatic switching on/off via humidity sensor.No setting of switch-on humidity necessary. Fan monitors the room humidity.Automatically ventilates depending on room humidity in stage 1 and stage 2.Operation without switch possible, optionally also switchable via separate switch.Switch-on delay adjustable in steps via easily accessible buttons (only with control via switch): 0/50/90/120 sec.Run-on time adjustable in steps via easily accessible buttons: 8/17/25 min. Run-on time 0 min only adjustable for control via separate switch.Set time is displayed by LEDs during adjustment.Concealed intake, with electrically operated internal damper.Not speed controllable.Operating ProgramsAdjustable via jumper in the device.Comfort program (preset)User present: Stage 1Run-on time: Stage 2Demand programUser present: Stage 2Run-on time: Stage 1Economy programUser present: Stage 1Run-on time: Stage 1Power programUser present: Stage 2Run-on time: Stage 2FeaturesIntelligently programmed small room fan for highest demands.2 power levels.Concealed intake through design cover.For ventilation.Combines large volume flow with high pressure strength.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Thermal overload protection.Suitable for continuous operation.Colour traffic white similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with maintenance-free ball bearings.Suitable for continuous operation.Installation InstructionsCompatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same place.Wall and ceiling mounting possible.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsAll ECA 150 ipro devices can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning notes.Installation / Operation / Maintenance Wiring DiagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation Notes ArticleECA 150 ipro KHVersionHumidity controlVolume flow200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-24.05 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power18 W / 22 WIMax0.11 AProtection classIP X5Power cable3/5 x 1.5 mm²Installation locationCeiling / WallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.5 kgWeight with packaging1.77 kgDamperIntegratedType of damperElectricNominal diameter150 mmWidth228 mmHeight228 mmDepth123.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CRun-on time8 min / 17 min / 25 min / Run-on time 0 min available when using an optional switch (e.g. light switch)Switch-on delay0 s / 50 s / 90 s / 120 s / Switch-on delay available when using an optional switch (e.g. light switch)Sound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free-field conditions

ECA 150 ipro RC - Brief InformationTwo-stage small room fan, DN 150, with radio receiver, master-slave operation only possible in a pure system, i.e. only with ECA 150 ipro ...RC... devices!ECA 150 ipro RC - Product DescriptionVersion with Radio ReceiverWith integrated 868 MHz radio receiver.On/Off via radio switch DS RC or separate control RLS RC.The two speeds can be selected either on the radio switch or on the control unit.Not speed-controllable.FeaturesRadio-controlled fan for the MAICOsmart exhaust system, with built-in 868 MHz radio receiver based on EnOcean technology.The fan can be operated with a double rocker switch (DS RC) (no wiring required between switch and fan).The fan can be installed in a master-slave network with other ECA 150 ipro RC/RCH/KRC/KRCH units (RLS RC required). A combination of ECA 150 ipro RC/RCH/KRC/KRCH with ECA 100 ipro RC/RCH or ER 100 RC is not possible.Two power levels.Concealed intake through design cover.For ventilation.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Traffic white colour similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsEasiest installation as the cover can be easily removed with a tool.Compatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same place.Electrical ConnectionElectrical connection flush-mounted.Safety NoticeThe fans comply with protection class IP X5 and can therefore be installed in protection zone 1 according to DIN VDE 0100-701.Details see planning notes chapter small room fans.Installation / Operation / Maintenance Wiring DiagramsInstallation instructions: pdf | onlineInstallation Notes ArticleECA 150 ipro RCVersionRadio receiverAirflow volume200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-11.18 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power15 W / 19 WIMax0.09 AProtection classIP X5Power cable3 x 1.5 mm²Installation locationCeiling / WallType of installationSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.61 kgWeight with packaging1.88 kgFlapNoneNominal diameter150 mmWidth228 mmHeight228 mmDepth189.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CSound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free field conditions

ECA 150 ipro RCH - Brief InformationTwo-stage small room fan, DN 150, with radio receiver and humidity control, master-slave operation only possible in a pure system, i.e. only with ECA 150 ipro ...RC... devices!ECA 150 ipro RCH - Product DescriptionVersion with Radio Receiver and Humidity ControlWith integrated 868 MHz radio receiver and humidity control.Barrier-free product due to automatic switching on/off via humidity sensor.No setting of the switch-on humidity necessary. The fan monitors the humidity level. Automatically ventilates depending on room humidity in stage 1 or stage 2.Can be switched with separate radio switch DS RC or separate control RLS RC.The two speeds can be selected either on the radio switch or on the control unit.Not speed-controllable.FeaturesRadio-controlled fan for the MAICOsmart exhaust system, with built-in 868 MHz radio receiver based on EnOcean technology.The fan can be operated with a double rocker switch (DS RC) (no cable laying between switch and fan necessary).The fan can be installed in a master-slave network with other ECA 150 ipro RC/RCH/KRC/KRCH (RLS RC required). A combination of ECA 150 ipro RC/RCH/KRC/KRCH with ECA 100 ipro RC/RCH or ER 100 RC is not possible.Two power levels.Concealed intake through design cover.For ventilation.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Traffic white colour similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsVery easy installation as the cover can be easily removed with a tool.Compatible with ECA predecessor models DN 150, as fixing holes and flush-mounted cable entry are in the same place.Electrical ConnectionElectrical connection flush-mounted.Safety NoticeThe fans comply with protection class IP X5 and can therefore be installed in protection zone 1 according to DIN VDE 0100-701.Details see planning notes chapter small room fans.Installation / Operation / Maintenance Wiring diagramsInstallation instructions: pdf | onlineInstallation notes ArticleECA 150 ipro RCHVersionRadio receiver and humidity controlAir volume200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-24.57 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power15 W / 19 WIMax0.09 AProtection classIP X5Power cable3 x 1.5 mm²Installation locationCeiling / WallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.62 kgWeight with packaging1.9 kgFlapNoneNominal diameter150 mmWidth228 mmHeight228 mmDepth189.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CSound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free field conditions

Small room fan ECA 150 ipro KRC internal shutter, radio, DN150Features:Made in Germany quality, super quiet, fan connection DN 150, protection class IP X5 for safety in the office, protection class IIFor a better indoor climate in the office or home, The low-noise small room fan - the elegant solution against humidity, unpleasant odours and mouldOn/off via radio switch or separate control. Uncomplicated one-man installation with standard tools - low-maintenance device. Speeds can be selected on the radio switch or on the control unit. Can be operated with double rocker switch. Not speed-controllable. Flush-mounted electrical connection. Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any office furnishing style Housing made of impact-resistant plasticSuitable for continuous operation. Energy-saving, robust motor with sealed ball bearings on both sidesDescription:Version with radio receiver: With integrated 868 MHz radio receiver. On/off via DS RC radio switch or separate RLS RC control unit. The two speeds can be selected either on the radio switch or on the control unit. Concealed intake, with electrically operated internal shutter. Not speed-controllable. Radio-controlled fan for the MAICOsmart extract air system, with built-in 868 MHz radio receiver, based on EnOcean technology. The fan can be operated with a double rocker switch (DS RC) (no cable routing required between switch and fan). The fan can be installed in a master-slave network with other ECA 150 ipro RC/RCH/KRC/KRCH (RLS RC required). A combination of ECA 150 ipro RC/RCH/KRC/KRCH with ECA 100 ipro RC/RCH or ER 100 RC is not possible. Two performance levels. Concealed intake through design cover. For ventilation. With VDE-GS mark. Protection class IP X5 for safety in the bathroom. Protection class II. Colour traffic white similar to RAL 9016. Housing made of impact-resistant plastic. Motor: Energy-saving, robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Extremely simple installation, as cover can be easily removed with tools. Compatible with ECA predecessor models DN 150, as the fixing holes and flush-mounted cable entry are in the same place. Electrical connection: Flush-mounted electrical connection. Safety note: The fans comply with protection class IP X5 and can therefore be installed in protection zone 1 in accordance with DIN VDE 0100-701. For details, see planning information chapter Kleinraumventilatoren.Artikel: ECA 150 ipro KRC, Version: Radio receiver, Delivery volume: 200 m3/h / 250 m3/h, Speed: 1672 1/min / 2189 1/min, Speed controllable: no, Reversibility: no, SEC average: -10.62 kWh/(m2*a), Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz, Rated power: 18 W / 22 W, IMax: 0.11 A, Protection rating: IP X5, Mains cable: 3 / 1.5 mm2, Installation location: Ceiling / wall, Installation type: Surface-mounted, Installation position: any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 1.685 kg, Weight with packaging: 1.961 kg, Flap: integrated, Flap type: electric, Nominal width: 150 mm, Width: 228 mm, Height: 228 mm, depth: 189.3 mm, width with packaging: 235 mm, height with packaging: 235 mm, depth with packaging: 200 mm, fluid temperature at IMax: 40 °C, sound pressure level: 33 dB(A) / 40 dB(A) / distance 3 m, free field conditions

ECA 150 ipro KRCH - Short InformationTwo-stage small room fan, DN 150, with electric internal damper, radio receiver and humidity control, master-slave operation only possible in a pure system, i.e. only with ECA 150 ipro ...RC... devices!ECA 150 ipro KRCH - Product DescriptionVersion with Radio Receiver and Humidity ControlWith integrated 868 MHz radio receiver and humidity control.Barrier-free product due to automatic switching on/off via humidity sensor.No setting of the switch-on humidity necessary. The fan monitors the humidity trend. Automatically ventilates depending on room humidity in stage 1 or stage 2.Can be switched with separate radio switch DS RC or separate control RLS RC.The two speeds can be selected either on the radio switch or on the control unit.Concealed intake with electrically operated internal damper.Not speed controllable.FeaturesRadio-controlled fan for the MAICOsmart exhaust system, with built-in 868 MHz radio receiver based on EnOcean technology.The fan can be operated with a double rocker switch (DS RC) (no cable routing between switch and fan necessary).The fan can be installed in a master-slave network with other ECA 150 ipro RC/RCH/KRC/KRCH (RLS RC required). A combination of ECA 150 ipro RC/RCH/KRC/KRCH with ECA 100 ipro RC/RCH or ER 100 RC is not possible.Two power levels.Concealed intake through design cover.For ventilation.With VDE-GS mark.Protection class IP X5 for safety in the bathroom.Protection class II.Traffic white colour similar to RAL 9016.Housing made of impact-resistant plastic.MotorEnergy-saving, robust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsEasiest installation as the cover can be easily removed with a tool.Compatible with ECA predecessor models DN 150, as mounting holes and flush-mounted cable entry are in the same place.Electrical ConnectionElectrical connection flush-mounted.Safety NoticeThe fans comply with protection class IP X5 and can therefore be installed in protection zone 1 according to DIN VDE 0100-701.Details see planning notes chapter small room fans.Installation / Operation / Maintenance Wiring DiagramsInstallation instructions: pdf | onlineInstallation Notes ArticleECA 150 ipro KRCHVersionRadio receiver and humidity controlAirflow volume200 m³/h / 250 m³/hSpeed1,672 rpm / 2,189 rpmSpeed controllable−Reversibility−SEC average-24.24 kWh/(m²*a)Voltage typeAlternating currentRated voltage230 VMains frequency50 HzRated power18 W / 22 WIMax0.11 AProtection classIP X5Power cable3 x 1.5 mm²Installation locationCeiling / WallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.8 kgWeight with packaging1.98 kgDamperIntegratedType of damperElectricNominal diameter150 mmWidth228 mmHeight228 mmDepth189.3 mmWidth with packaging235 mmHeight with packaging235 mmDepth with packaging200 mmConveyed medium temperature at IMax40 °CSound pressure level33 dB(A) / 40 dB(A) / Distance 3 m, free-field conditions

ECA piano Standard - Brief InformationEspecially quiet small room fan, standard versionECA piano Standard - Product DescriptionStandard VersionOn/Off via light switch or separate switch.Speed controllable.Due to the phase-cutting technology, a physically caused humming noise may occur at low speeds.FeaturesEspecially quiet thanks to innovative piano impeller.Cover removable without tools for cleaning.Compatible with ECA 100 ipro and ECA predecessor models DN 100, same screw hole positions and cable entry.With VDE mark.Protection class IP X4 for safety in the bathroom.Protection class II.Integrated backdraft flap without spring, durable and stable.Colour traffic white similar to RAL 9016.Suitable for pipe DN 100.Housing made of impact-resistant plastic.Thermal overload protection.MotorRobust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsEasiest installation as cover is removable without tools.Wall and ceiling mounting possible; for ceiling mounting, a hole in the cover is necessary.Electrical ConnectionElectrical connection flush-mounted.Safety InstructionsAll ECA piano devices can be used in protection zone 2 according to DIN VDE 0100-701.Details see planning instructions. Installation / Operation / Maintenance Wiring diagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation instructions ArticleECA piano StandardVersionStandard versionAirflow volume80 m³/hSpeed2,400 rpmSpeed controllable✔Reversibility−Voltage typeAlternating currentRated voltage230 VMains frequency50 Hz / 60 HzRated power8 WIMax0.06 AProtection classIP X4Power cable3 x 1.5 mm²Installation locationWall / CeilingInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight0.5 kgWeight with packaging0.61 kgNominal diameter100 mmWidth151 mmHeight151 mmDepth104 mmWidth with packaging160 mmHeight with packaging160 mmDepth with packaging130 mmConveyed medium temperature at IMax40 °CSound pressure level26 dB(A) / Distance 3 m, free field conditions

Small room fan AKE 150 Basement dehumidification, 250 m3/h, DN 150 AKE 150/1 - Brief InformationAutomatic basement dehumidification, DN 150, air volume 250 m³/hAKE 150/1 - Product DescriptionDesignApplication area up to approx. 70 m² per fan.Versatile system expandability: connection of a supply air fan (e.g. ECA 15/4 E) possible to increase air exchange.FeaturesFully automatic, intelligent basement dehumidification for the highest demands.Permanent comparison of absolute humidity indoors and outdoors: fan ventilates independently when the absolute humidity inside is higher than outside.No maintenance or manual control required: install once and the system operates automatically.Additional fans without their own dew point control can be connected directly to the AKE up to max. 1.2 A and benefit from the intelligence.Fans > 1.2 A can be connected via an intermediate relay or contactor, allowing larger or multiple rooms to be dehumidified via the AKE.Concealed intake through design cover.Barrier-free product, as automatic switching on/off without additional switches.Fan monitors room humidity.Frost protection function: system switches off automatically at indoor temperatures below 5 °C.Garage dehumidification: optional deactivation of frost protection for unheated rooms.Additional manual operation for 30 minutes can be switched on and off via a push button.No additional installation of a switch to the device necessary.Additional manual operation with external push button or switch possible.Automatic push button / switch detection.Status and function display via LEDs.Scope of delivery:FanExternal closure flapSensors1.5 m connection cableTraffic white colour, similar to RAL 9016.Housing made of impact-resistant plastic.Thermal overload protection.Protection class II.Frost ProtectionTo prevent the room from cooling down, the AKE has a frost protection function. The fan switches off automatically at indoor temperatures below 5 °C.Garage DehumidificationThe frost protection function of the AKE can be bypassed via DIP switch to allow year-round dehumidification of unheated rooms.MotorEnergy-saving, robust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsSimple installation:AKE 100: Core hole drilling 105 mm, or 120 mm when installed with accessory wall sleeve WH 100.AKE 150: Core hole drilling 155 mm, or 170 mm when installed with wall sleeve WH 150.Wall and ceiling mounting possible.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Surface-mounted installation for AKE 100 with accessory spacer frame ECA-DR.Installation / Operation / Maintenance Wiring diagramsInstallation manual: pdf | onlineSafety instructions Small room fans: pdf | online ArticleAKE 150/1Air volume250 m³/hSpeed2,189 1/minSpeed controllable−Reversibility−SEC average-24.48 kWh/(m²*a)Type of currentAlternating currentRated voltage230 VMains frequency50 HzRated power19 WStand-by power consumption2 WIMax0.09 AProtection typeIP X4Power cable5 x 1.5 mm²Installation locationWallPlace of installationBasement / GarageType of installationSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight1.8 kgWeight with packaging2.37 kgNominal diameter150 mmCable length1.5 mWidth228 mmHeight228 mmDepth178.3 mmWidth with packaging303 mmHeight with packaging273 mmDepth with packaging303 mmWall thicknessmax. 0.85 m (if 1 m cable length is not sufficient, please order the 6 m sensor cable additionally)Medium temperature at IMax40 °CSound pressure level40 dB / Distance 3 m, free field conditions

ECA 120 - Brief InformationWith fixed inner grilleECA 120 - Product DescriptionStandard VersionSpeed controllable.Due to the phase-cutting technology, a physically caused humming noise may occur at low speeds.FeaturesHigh delivery volume despite compact design.Combines large delivery volume with pressure strength.Thermal overload protection.Housing made of impact-resistant plastic.Protection class II.With VDE-GS mark, exception: ECA 120 24 V.With protective seals against the ingress of condensate when installed in ceilings.Speed control optionally available for ECA fans in standard version.Colour traffic white similar to RAL 9016.MotorRobust motor with ball bearings, maintenance-free.Suitable for continuous operation.Installation InstructionsSimple, quick removal of the cover.Quick fastening of the fan in the duct by 2 clamping springs.Electrical ConnectionElectrical connection optionally surface-mounted or flush-mounted.Safety InstructionsECA 120 devices with protection class IP 45 can be used in protection zone 1 according to DIN VDE 0100-701.Details see planning instructions.Installation / Operation / Maintenance Wiring diagramsSafety instructions small room fans: pdf | onlineInstallation instructions: pdf | onlineInstallation instructions ArticleECA 120VersionStandard versionDelivery volume170 m³/hSpeed2,600 1/minSpeed controllable✔Reversibility−Type of voltageAlternating currentRated voltage230 VMains frequency50 Hz / 60 HzPower consumption19 WIMax0.14 AProtection classIP 45Power cable3 x 1.5 mm²Installation locationWallInstallation typeSurface-mountedInstallation positionAnyMaterialPlasticColourTraffic white, similar to RAL 9016Weight0.9 kgWeight with packaging1.05 kgNominal size120 mmWidth171 mmHeight171 mmDepth114 mmWidth with packaging180 mmHeight with packaging180 mmDepth with packaging140 mmMedium temperature at IMax40 °CSound pressure level42 dB(A) / Distance 3 m, free-field conditions

ECA piano TC small room fan with adjustable overrun, DN100Features:Made in Germany quality, super quiet, fan connection DN 100, protection class IP X4 for safety in the bathroom, protection class IIFor a better indoor climate in the bathroom or WC, The low-noise exhaust air fan - the elegant solution against moisture, unpleasant odours and mouldSimple operation by switching on/off with the light switch or a separate switch - low-maintenance device. Uncomplicated one-man installation with standard tools. Run-on time adjustable from approx. 3 min - approx. 25 min. Not speed-controllable. Continuous power connection required for adjustable run-on time (4-core cable to fan) Attractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation, thermal overload protection. Energy-saving, robust motor with ball bearingDescription:Version with adjustable run-on time: On/off via light switch or separate switch. With VDE mark. Run-on time adjustable from approx. 3 min to approx. 25 min. Not speed-controllable. Particularly quiet thanks to innovative piano impeller. Cover can be removed for cleaning without tools. Compatible with ECA 100 ipro and ECA predecessor models DN 100, same position of screw holes and cable entry. Protection class IP X4 for safety in the bathroom. Protection class II. Integrated springless non-return flap, durable and stable. Colour traffic white similar to RAL 9016. Suitable for DN 100 pipe. Housing made of impact-resistant plastic. Thermal overload protection. Motor: Robust motor with ball bearing, maintenance-free. Suitable for continuous operation. Installation instructions: Extremely simple installation as cover can be removed without tools. Wall and ceiling mounting possible, hole in cover required for ceiling mounting. Electrical connection: Flush-mounted electrical connection. Safety instructions: All ECA piano devices can be used in protection zone 2 in accordance with DIN VDE 0100-701. For details see Planungshinweise.Artikel: ECA piano TC, Version: Adjustable overrun, Delivery volume: 80 m3/h, Speed: 2400 1/min, Speed controllable: no, Reversibility: no, Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Rated power: 8 W, IMax: 0.06 A, Protection rating: IP X4, Mains cable: 5 / 1.5 mm2, Installation location: Wall / ceiling, Installation type: Surface-mounted, Installation position: Any, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.485 kg, Weight with packaging: 0.615 kg, Nominal width: 100 mm, Width: 151 mm, Height: 151 mm, Depth: 104 mm, Width with packaging: 160 mm, Height with packaging: 160 mm, Depth with packaging: 130 mm, Conveying medium temperature at IMax: 40 °C, Run-on time: 3 min - 25 min, Sound pressure level: 26 dB(A) / distance 3 m, Free field conditions