Flat channel with internal reinforcement and fastening strip 220 mm, L = 1000 mm

Flat trunking nipple connector made of galvanised sheet steel For direct connection of duct to duct Flat duct system for controlled domestic ventilation or extractor fans 50 mm height Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1 Insertion depth per side 40 mm. On request: Special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.

Horizontal flat duct bend made of galvanised sheet steel. Area of application: Flat duct bends are used as connecting elements in supply and exhaust air ducts for controlled domestic ventilation. They can also be used in exhaust air ducts for extractor bonnets in the kitchen or as part of a supply air duct for fireplaces and stoves. We recommend using our aluminium adhesive tape or aluminium-laminated cold-shrink tape to seal the joints. Both options offer sufficient protection against pressure loss in your duct system. The Intelmann flat duct system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.

Flat duct socket connector for moulded parts made of galvanised sheet steel. For connecting moulded part to moulded part For connecting two pieces of moulding (bend with bend, bend with T-piece, etc.); NOT suitable for connecting flat duct to flat duct! Flat duct system for controlled domestic ventilation or extractor hoods; 50 mm height; Material: Sendzimir galvanised sheet steel, zinc coating 275g/m², non-combustible according to DIN 4102 class A1; Insertion depth per side 40 mm; On request: special parts / dimensions, different heights, also in stainless steel 1.4301 and 1.4571 and aluminium. The Intelmann flat trunking system is designed according to the socket-nipple principle Flat ducts are connected to each other with flat duct nipple connectors Moulded parts (bends, T-pieces, transition pieces) are connected to each other with a sleeve This allows all moulded parts to be inserted into the trunking. No further connection is required for this.

Connection piece for disc valve / deflector / elbow End piece From flat duct to spiral duct Socket according to EN1506, z.b. For direct connection of a disc valve Material: galvanised steel, non-combustible to DIN 4102 class A1 Flat duct system for plugging

MEZ-PLAST 580, 310 ml cartridge, silver-grey Sealing compound for sealing air duct systems and technical installations without silicone an alternative to soldering very good adhesion to all metals Fast curing sealant High chemical resistance Product properties: good adhesion to greasy, oily substrates and all metals Permanently elastic resistant to ageing, weathering and UV radiation antibacterial and fungicidal (against fungal attack) toxicologically harmless Resistant to many chemicals fulfils the hygienic requirements for use in for use in clean rooms and the specifications of the VDI 6022 guideline. can be used on lightly oiled, corrosion-preserved metals without degreasing without silicone, without nitrogen CFC-free no AOX components no lead compounds no mercury compounds no chromium compounds MEZ-PLAST is lead- and chromate-free and therefore food-safe according to the law Technical data Raw material base: acrylic resin, solvent-curing Curing time: approx. 4 mm in the first 24 h at +23°C and 50% r.F. Temperature resistance: - 40°C to +80°C (permanent) - 40°C to +100°C max. 1 h Processing temperature: +2°C to +60°C Shore A hardness: 38 Density: 1.05 g/m3 Primer: no Skin formation time: 10 min. at 23°C and 50% r.F. Coating compatibility: yes, preliminary tests required Paintability: yes, preliminary tests required Shelf life: 12 months Storage: protect from frost Flash point: below +21°C /- 4°C Hazard class: A1 Area of application: Sticks and adheres to all metals for sealing in ventilation ducts and plant construction Bonding and sealing in clean rooms, chip production, etc. Notes: - MEZ-PLAST is ready to use and can be applied without pre-cleaning and degreasing the areas to be sealed using a brush, - spatula or spraying equipment. - can be painted over after curing - A slight shrinkage may occur due to evaporation of the solvents contained.

MEZ-PLAST 590 SMP, 300 ml cartridge, grey MEZ-PLAST 590 SMP is an elastic, fast-setting one-component sealant for HVAC applications, tested in accordance with DIN EN ISO 846.Application: Suitable for HVAC systems in accordance with VDI 6022 / EN 15780, as well as for grease exhaust air and clean rooms. With EC 1 Plus classification, MEZ-PLAST SMP fulfils the highest requirements for sustainable construction. Complies with DGNB 2018.Properties:Fungicidal and bactericidalNon-corrosiveQuickly tack-free surfaceFree from silicone and isocyanateVery low shrinkageGood weathering & ageing resistanceSolvent-freeSkin formation: Approx. 15 - 20 min.Curing: 3 - 4 mm on the 1st dayProcessing temperature: +5°C to +35°CTemperature resistance: -40°C to +90°CShelf life: 12 monthsREACH regulationSVHC ≤ 0.1 %MEZ-PLAST 590 SMP does not contain any substances of very high concern above 0.1%. PRODUCT HIGHLIGHTS: Low emission Silicone-free Free from solvents & isocyanateHigh temperature resistance

The spray is suitable for re-galvanising and repairing damaged areas on galvanised parts, welds and interfaces in steel construction and the hobby sector. It takes on the task of corrosion protection and, due to its colour similarity with freshly galvanised materials, creates an optical balance. Gebhardt-Stahl Zink-Alu-Spray is a quick-drying anti-corrosion coating based on selected binders with a very high solids content. Fast drying High coverage, therefore economical to use Suitable substrates are steel, cast iron, aluminium, zinc and many more.

Self-tapping screws 4.2x13 mm with hexagon head and pressed-on washer, case-hardened galvanised steel, self-tapping DIN 7504 KThese screws are manufactured in galvanised steel. Self-tapping screws with 6KT head and pressed-on washer are characterised by their head shape (hexagon head with flange) and have a sheet metal thread. When you purchase a packaging unit of DIN 7504 K self-drilling screws, you receive 100 screws. Further important information about the article DIN 7504 Form K - Self-drilling screw with 6KT head with pressed-on washer : Weight per 100 pieces: 0.193 kg d: 4.2 mm; s: 7 mm; l: 13 mm; k: 4.1 mm; lp: 4.5 mm Self-drilling screws made of steel, electrogalvanised, high-quality industrial quality. Self-drilling screws for mounting sheet metal, ventilation ducts, flat ducts, fans, metal rails and car parts. The screws can be easily fastened with a cordless screwdriver without pre-drilling

VERSATILE USE: Aluminium adhesive tape is perfect for joints and seals in insulation, wiring and pipe work. It can also be used for repairs to metal surfaces such as vehicle bodies and guttering. No toolbox should be without it!STRONG ADHESIVE: Adheres immediately to metallic surfaces and provides an airtight and watertight seal. Thanks to the long-lasting adhesive, this aluminium tape provides reliable insulation, whether it is used indoors or outdoors. Heat-resistant from -30 °C to +130 °CEASY TO APPLY: Simply cut to the desired size, remove from the backing paper and apply.Aluminium adhesive tape for sealing duct or corrugated pipe connections Length: 45m Width: 50mm Thickness: 30µ Application range from -30 to +130°C