Butterfly valve with Belimo CM24-L Ø 160 mm
€135.18
Available immediately, delivery time: 1-3 working days
Product information "Butterfly valve with Belimo CM24-L Ø 160 mm"
- Shut-off damper steel, galvanised
- with EPDM sealing lips for airtight installation to DIN EN 12237 class D best class of this standard
- Damper blade with EPDM sealing lip tight-closing to DIN EN 1751 class 4 best class of this standard
- Damper blade with two bearings; damper with motorised bracket, rotatable for actuator mounting at any position, 360° around damper shaft
- With Belimo CM24-L damper actuator for open/close control of dampers, AC/DC 24 V, 2 NM torque for dampers up to 0.4 m² damper area
- The shut-off damper is inserted between two ventilation ducts
Technical data sheet Belimo CM24-L
Electrical data
Rated voltage AC/DC 24 V
Nominal voltage Frequency 50/60 Hz
Functional range AC 19.2...28.8 V / DC 19.2...28.8 V
Power consumption in operation 0.5 W
Power consumption idle position 0.2 W
Power consumption Dimensioning 1 VA
Power supply / control connection Cable 1 m, 3 x 0.75 mm²
Parallel operation Yes (observe power data)
Functional data
Motor torque min. 2 Nm
Direction of rotation Motor anti-clockwise
Manual adjustment with magnet
Angle of rotation 0...287.5°,
Angle of rotation Note without limit: endless
with one end stop clip Z-ESCM: 315°
Running time motor 75 s / 90°
Motor sound power level 35 dB(A)
Axle drive Universal clamping block 6...12.7 mm
Mechanical position indicator, clip-on (with integrated magnet for gear disengagement)
(with integrated magnet for gear disengagement)
Safety
Protection class IEC/EN III safety extra-low voltage (SELV)
Protection class UL UL Class 2 Supply
Protection class IEC/EN IP54
Protection class NEMA/UL NEMA 2, UL Enclosure Type 2
EMC CE according to 2014/30/EU
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
UL cULus certification in accordance with UL 60730-1A, UL 60730-2-14
and CAN/CSA E60730-1:02
Mode of operation Type 1
Rated impulse voltage Supply /
Control
##########_48__ kV
Degree of pollution of the environment 3
Ambient temperature -30...50°C
Storage temperature -40...80°C
Ambient humidity 95% r.H, non-condensing
Maintenance maintenance-free
Weight approx.
Weight approx. 0.28 kg
Allgemeines Warnzeichen
Warnung vor Handverletzungen
Warnung vor Absturzgefahr
Customers also bought
Spiral duct for the installation of ventilation systemsSpiral duct ØD = inner diameter [mm]Length 1000 mmMaterial: Galvanised sheet steelDesign in accordance with DIN EN 12237Tightness class D according to DIN EN 1507 (highest class of the standard)Intelmann spiral duct Application areas: The Intelmann spiral duct or spiral seam duct is used for air routing of extract air, outside air, exhaust air and supply air in centralised domestic ventilation or controlled domestic ventilation with heat recovery. The ventilation duct is made of galvanised sheet steel. The diameter refers to the internal diameter of the duct. Connecting the Intelmann spiral ducts in the ventilation system: Nipples or pipe connectors are used to connect the spiral ducts in a ventilation system. Fittings such as bends, branch pieces or T-pieces can be connected directly to the spiral duct. Sockets are used to connect fittings (bends / branch pieces / T-pieces) to each other. A spiral duct is compatible with all other fittings with the same diameter. Two spiral ducts are connected with a nipple.