Maico ECA 100 ipro small room fan 0084.0200

Aluminium flexible pipe AFR 100 flexible, five-ply grooved, DN100Features:Quality Made in GermanyAluminium flexible pipe - as a connection pipe to the main pipeNon-combustible in accordance with DIN 4102 class A1. For use as a connection pipe to the main pipe.Attractive design - compatible with any furnishing styleSuitable for continuous operation.Description:Flexible five-layer grooved aluminium conduit for use as a connection line to the main line in accordance with DIN 18017-3. Non-combustible in accordance with DIN 4102 class A1. Length specifications: Stretched length: AFR 100, Max. Operating pressure: 2500 Pa, Installation type: Flush-mounted, Material: Aluminium, Weight: 0.915 kg, Weight with packaging: 1.03 kg, Suitable for nominal width: 100 mm, Length: 10 m, Width: 10000 mm, Height: 115 mm, Depth: 115 mm, Width with packaging: 403 mm, Height with packaging: 122 mm, Depth with packaging: 122 mm, Ambient temperature: 100 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for residential ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

AKE/1 - Brief informationControl unit AKE/1 incl. 2 pcs. AKE FFT humidity and temperature sensor (4m cable, can be extended on site to max. 30m) for fully automatic cellar dehumidification in conjunction with various fansAKE/1 - Product descriptionProduct featuresFully automatic, intelligent cellar dehumidification control for the highest demands.Permanent equalisation of the absolute humidity indoors and outdoors: Connected fans ventilate independently if the absolute humidity in the room is higher than outside.No maintenance or manual control required: install once and the system works automatically.Operation of fans up to a total (supply and extract air fan) of 600 W and 3 A.For the use of fans > 600 W and 3 A as well as three-phase fans, a circuit breaker must be installed between the control unit and the fan.Barrier-free product, as it switches on/off automatically without additional switches.Control unit monitors the room humidity via integrated humidity/temperature sensors.Frost protection function: system switches off at indoor temperatures below 5 °C.Additional manual operation for 30 minutes can be switched on and off again using a button on the control unit.No additional installation from the switch to the device necessary.Additional manual operation with external button or switch possible.Automatic button / switch detection.Status and function display via LEDs.Compact dimensions: Control unit 160 x 110 x 90 mm, outdoor sensor Ø50 mm, height 13 mm.Scope of delivery: Control unit, 2 sensors with 4 m cable length each.Sensor cable can be extended on site with LIYY 4x0.25 mm² cable to max. 30 (separate installation required).Housing made of impact-resistant plastic.IP protection: Control unit IP40 / outdoor sensor IP54.Frost protection: To prevent the room from cooling down, the AKE has a frost protection function. This automatically switches off the connected fan(s) at indoor temperatures of less than 5 °C.Garage dehumidification: optional switch-off of the frost protection function for unheated rooms.Suitable for continuous operation.Installation instructionsSimple installation: Wall mounting.Electrical connection: Surface-mounted.

Hygrostat HY 230 External control elementFeatures:Made in Germany quality, protection class IP 30 for safety in the homeHygrostat - for simple controlExternal control element. Used for dehumidifying or humidifying closed rooms. The operating mode can be selected using a dip switch.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:The HY 230 or HY 230 I electronic hygrostat is used for dehumidifying or humidifying closed rooms. It is suitable for all living areas and commercial premises, including damp rooms such as bathrooms. Bathrooms (please observe protection class when installing), washrooms and drying rooms. The hygrostat uses an internal sensor to detect the room humidity and switches the fans, heat recovery units, humidifiers or dehumidifiers on and off depending on the set target value. The HY 230 or HY 230 I is either mounted directly on a flush-mounted box or mounted on the wall using the APM HY 230 surface-mounting set. The operating mode dehumidification (factory setting) or humidification can be set during commissioning using a dip switch on the circuit board. A red LED in the housing indicates the switching status of the relay angezeigt.Artikel: HY 230, Voltage type: AC, Rated voltage: 230 V, Output: 230 V, Mains frequency: 50 Hz, Relative humidity measuring range: 20 % - 80 %, Installation type: Surface-mounted, Material: Plastic, Colour: Pure white, similar to RAL 9010, Weight: 0.0753 kg, Weight with packaging: 0.089 kg, Width: 71 mm, Height: 71 mm, Depth: 27 mm, Width with packaging: 75 mm, Height with packaging: 80 mm, Depth with packaging: 36 mm, Ambient temperature: 0 °C to 50 °C, Operating element: External, Sensor tolerance, relative humidity: 5 %, Switching differential, relative humidity: 2.5 %, Max. permissible switching current: 10 A / 4 A / cos phi = 1, 230 V AC / cos phi = 0.6, 230 V AC, Max. permissible inrush current: 16 A, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: yes, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Door ventilation grille MLK 45 white white, length approx. 450 mmFeatures:Quality Made in GermanyDoor ventilation grille - for easy installationDoor cut-out: 436 x 76 mm, external dimensions: 457 x 92 mmAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:Door ventilation grille for bathroom, WC, kitchen. Free cross-section in accordance with FeuVo 80 and TRGI 86. MLK 30: Door cut-out: 275 x 105 mm, external dimensions: 295 x 120 mm. MLK 45: Door cut-out: 436 x 76 mm, external dimensions: 457 x 92 mm.Artikel: MLK 45 white, air direction: ventilation, installation: inside, installation location: door, material: plastic, plastic specifications: Polystyrene, PVC-free, Colour: white, Weight: 0.27 kg, Weight with packaging: 0.31 kg, Free cross-section: 154 cm2, Width: 457 mm, Height: 92 mm, Depth: 38 mm, Width with packaging: 458 mm, Height with packaging: 93 mm, Depth with packaging: 36 mm, Minimum door leaf thickness: 35 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: yes, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Speed controller STX 1.5 Rated voltage 230 V, infinitely variableFeatures:Made in Germany quality, protection class IP 44 for safety in the homeSpeed controller - for easy installationStepless control. Minimum speed adjustable. Splash-proof. With LED operating indicator. Switch on the fan by turning the control knob. Includes spare fuse.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Speed controller for infinitely variable control of fans. Minimum speed adjustable. Can be used for surface and flush mounting, exception: STX 4 only for surface mounting. Functional principle: Phase angle control. Recommended distance from radio and television sets: 3 m. Switch on the fans at maximum speed by turning the control knob. Further turning reduces the speed. Splash-proof. Built-in temperature cut-out. Orange LED operating indicator. CE mark. Including spare fuse. Additional switching contact (230 V), e.g. for activating a flap. Due to the phase control technology, a physically induced humming noise may occur in the lower speed range. Therefore, in rooms requiring low-noise fan operation, use 5-step transformers TRE... for speed control. Installation on walls possible, avoid installation on ceilings due to temperature development. STX 1.5, STX 2.5: Width x height x depth when used for surface mounting: 82 mm x 89 mm x 69 mm, width x height x depth when used for flush mounting: 50 mm x 50 mm x 33 mm, STX 4: Width x height x depth when used for surface mounting: 82 mm x 89 mm x 69 mmArticle: STX 1.5, Voltage type: AC, Rated voltage: 230 V, Maximum load: 1.5 A, Minimum load: 0.1 A, Protection rating: IP 44, Installation type: Surface-mounted or flush-mounted, Colour: White, similar to RAL 9010, Weight: 0.1638 kg, Weight with packaging: 0.196 kg, Width: 82 mm, Height: 89 mm, Depth: 69 mm, Width with packaging: 85 mm, Height with packaging: 95 mm, Depth with packaging: 70 mm, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: yes, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Delay time switch VZ 24 C Run-on time 1.5 to 24 minFeatures:Made in Germany quality, protection class IP 40 for safety in the homeDelay timer - for simple operationControl of run-on time and switch-on delay. Can be operated using standard switches or push-buttons. Switch-on delay 0-150 s, run-on time 1.5-24 min.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Delay timer for controlling the switch-on delay and run-on time of fans. Can be operated using standard switches. VZ 24 C: Can be operated via standard switches or push-buttons. Interference-proof in accordance with EN 61000-4-5 (at 1000 V to 4000 V). If necessary, take additional interference suppression measures (L, C or RC elements, protective diodes, varistors). Test mark: VDE.Artikel: VZ 24 C, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Maximum load: 1.25 A, Protection rating: IP 40, Weight: 0.012 kg, Weight with packaging: 0.016 kg, Width: 20 mm, Height: 13 mm, Depth: 35 mm, Width with packaging: 20 mm, Height with packaging: 13 mm, Depth with packaging: 35 mm, Ambient temperature: 0 °C to 50 °C, Remote control: no, Run-on time: 1.5 min - 24 min, Switch-on delay: 0 s - 150 s, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Delay time switch VZ 6 Run-on time 6 minFeatures:Made in Germany quality, protection class IP 40 for safety in the homeDelay timer - for simple operationControl of run-on time and switch-on delay. Can be operated using standard switches or push-buttons. Switch-on delay 50 s, run-on time 6 min.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Delay timer for controlling the switch-on delay and run-on time of fans. Can be operated using standard switches. VZ 24 C: Can be operated via standard switches or push-buttons. Interference-proof in accordance with EN 61000-4-5 (at 1000 V to 4000 V). If necessary, take additional interference suppression measures (L, C or RC elements, protective diodes, varistors). Test mark: VDE.Artikel: VZ 6, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Maximum load: 1.25 A, Protection rating: IP 40, Weight: 0.012 kg, Weight with packaging: 0.016 kg, Width: 20 mm, Height: 13 mm, Depth: 35 mm, Width with packaging: 20 mm, Height with packaging: 13 mm, Depth with packaging: 35 mm, Ambient temperature: 0 °C to 50 °C, Remote control: no, Run-on time: 6 min, Switch-on delay: 50 s, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

FE 100/1 AP window installation kit with automatic outer flapFeatures:Made in Germany quality, super quietWindow installation kit - for easy installation in windows and thin wallsSimple installation thanks to interlocking adapters and threaded sockets. Electrical connection to the terminal strip in the housing. Scope of delivery: External flap AP or external grille SG, 3 x spacer frames, 2 x sealing rings, threaded connectors, 3 x screws for fan fastening, strain relief bracket with 2 x screws, cable sheath, installation instructionsAttractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation.Description:For installation in windows and thin walls. Colour traffic white similar to RAL 9016, housing made of impact-resistant plastic. Scope of delivery: External flap AP or external grille SG, 3 x spacer frames, 2 x sealing rings, threaded connectors, 3 x screws for fan fastening, strain relief bracket with 2 x screws, cable grommet, installation instructions. Installation instructions: Simple installation in the window cut-out thanks to interlocking adapter and threaded spigot. Pane thickness at least 3 mm, pane spacing up to 75 mm. Pane cut-out 115 to 120 mm. Not suitable for installation in hinged double windows. Electrical connection: To the terminal strip in the housing of the ECA 100 ipro...Article: FE 100/1 AP, Installation location: Window / thin wall, Installation position: Horizontal, Material: Plastic, impact-resistant, Colour: Traffic white, similar to RAL 9016, Weight: 0.3964 kg, Weight with packaging: 0.482 kg, Width: 150 mm, Height: 150 mm, Depth: 103 mm, Width with packaging: 157 mm, Height with packaging: 157 mm, Depth with packaging: 123 mm

Delay time switch VZ 12 Run-on time 12 minFeatures:Made in Germany quality, protection class IP 40 for safety in the homeDelay timer - for simple operationControl of run-on time and switch-on delay. Can be operated using standard switches or push-buttons. Switch-on delay 50 s, run-on time 12 min.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Delay timer for controlling the switch-on delay and run-on time of fans. Can be operated using standard switches. VZ 24 C: Can be operated via standard switches or push-buttons. Interference-proof in accordance with EN 61000-4-5 (at 1000 V to 4000 V). If necessary, take additional interference suppression measures (L, C or RC elements, protective diodes, varistors). Test mark: VDE.Artikel: VZ 12, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Maximum load: 1.25 A, Protection rating: IP 40, Weight: 0.012 kg, Weight with packaging: 0.016 kg, Width: 20 mm, Height: 13 mm, Depth: 35 mm, Width with packaging: 20 mm, Height with packaging: 13 mm, Depth with packaging: 35 mm, Ambient temperature: 0 °C to 50 °C, Remote control: no, Run-on time: 12 min, Switch-on delay: 50 s, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

FE 100/1 SG window installation kit with fixed outer flapFeatures:Made in Germany quality, super quietWindow installation kit - for easy installation in windows and thin wallsSimple installation thanks to interlocking adapters and threaded connectors. Electrical connection to the terminal strip in the housing. Scope of delivery: External flap AP or external grille SG, 3 x spacer frames, 2 x sealing rings, threaded connectors, 3 x screws for fan fastening, strain relief bracket with 2 x screws, cable sheath, installation instructionsAttractive design with elegant front panel made of impact-resistant plastic - Neutral white colour similar to RAL 9016, compatible with any bathroom furnishing style Housing made of impact-resistant plasticSuitable for continuous operation.Description:For installation in windows and thin walls. Colour traffic white similar to RAL 9016, housing made of impact-resistant plastic. Scope of delivery: External flap AP or external grille SG, 3 x spacer frames, 2 x sealing rings, threaded connectors, 3 x screws for fan fastening, strain relief bracket with 2 x screws, cable grommet, installation instructions. Installation instructions: Simple installation in the window cut-out thanks to interlocking adapter and threaded spigot. Pane thickness at least 3 mm, pane spacing up to 75 mm. Pane cut-out 115 to 120 mm. Not suitable for installation in hinged double windows. Electrical connection: To the terminal strip in the housing of the ECA 100 ipro...Article: FE 100/1 SG, Installation location: Window / thin wall, Installation position: Horizontal, Material: Plastic, impact-resistant, Colour: Traffic white, similar to RAL 9016, Weight: 0.4068 kg, Weight with packaging: 0.493 kg, Width: 150 mm, Height: 150 mm, Depth: 103 mm, Width with packaging: 158 mm, Height with packaging: 158 mm, Depth with packaging: 123 mm

Outdoor air diffuser ALD 10 infinitely variableFeatures:Quality Made in GermanyFresh air diffuser - for decentralised home ventilationInfinitely variable regulation of the air flow. No electrical connection necessary. G2 filter. Scope of delivery: inner part, dust or insect filter, wall sleeve up to 500 mm, outer grille with fly screenAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:Fresh air diffuser for draught-free, decentralised home ventilation. Stepless regulation of the air flow. No electrical connection necessary. Packaging unit: Inner part, dust or insect filter, wall sleeve up to 500 mm, outer grille with fly screen. Accessories: Storm protection ALDS 10, replacement filter ALDF 10.Artikel: ALD 10, Air direction: Ventilation, Max. Volume flow: 32 m3/h / At 10 Pa, Installation location: Wall, Material: Plastic, Colour: Pure white, similar to RAL 9010, Weight: 0.983 kg, Weight with packaging: 1.21 kg, Filter type: Dust filter, Filter class: ISO Coarse 30 % (G2), Flap type: Manual, Nominal width: 100 mm, Width: 150 mm, Height: 150 mm, Depth: 580 mm, Width with packaging: 280 mm, Height with packaging: 155 mm, Depth with packaging: 280 mm, Ambient temperature: 60 °C, Rated max. Element standard sound level difference Dn,w: 31 dB, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

External grille SG 100 B for aeration and ventilation, DN100, brownFeatures:Quality Made in GermanyExternal grille - for easy installationWith concealed screw holes. Sealing tape included in the scope of delivery. External wall connection when using wall sleeve WH 100 & 120 & 150. Weather and UV-resistant plastic housingAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:External grille for ventilation. External wall connection when using wall sleeve WH100 & 120 & 150. SG 100 & 120 & 150/1: With concealed screw holes. Fly screen accessories FG 100 & 120 & 150 can be used. SG 100 B: brown. SG 15: With galvanised protective grille. Sealing tape included in the scope of delivery. Replacement air filter for SG 120: SF 120.Artikel: SG 100 B, Air direction: Ventilation, Installation: Outside, Installation location: Wall, Installation type: Surface-mounted, Material: Plastic, Weather-resistant, UV-resistant, Colour: Chestnut brown, similar to RAL 8015, Weight: 0.1 kg, Weight with packaging: 0.127 kg, Suitable for nominal width: 100 mm, Width: 150 mm, Height: 150 mm, Depth: 51.5 mm, Width with packaging: 151 mm, Height with packaging: 151 mm, Depth with packaging: 55 mm, Ambient temperature: 60 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no, With wire mesh: no, With insect screen: no, With pressure relief damper, intake: no, With pressure relief damper, exhaust: no, With counter-rotating damper valve: no, With co-rotating damper valve: no, With installation frame: no, Lockable: no, Motorised: no

Run-on relay NRS 10 for setting the fan run-on timeFeatures:Made in Germany quality, protection class IP 20 for safety in the homeRun-on relay - for simple operationSetting the run-on time 0.5-20 min. Actuation via switch-off switch, push-button and door contact switch possible. Installation with side air required.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Run-on relay for setting the fan run-on time. Can be operated using standard off switches, push-buttons and door contact switches. For thermal reasons, installation with side air notwendig.Artikel: NRS 10, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Maximum load (inductive load): 2.5 A, Maximum load (resistive load): 10 A, Protection rating: IP 20, Installation type: Switch cabinet, Weight: 0.075 kg, Weight with packaging: 0.09 kg, Width: 17.5 mm, Height: 90 mm, Depth: 73 mm, Width with packaging: 27 mm, Height with packaging: 93 mm, Depth with packaging: 74 mm, Remote control: no, Run-on time: 0.5 min - 20 min, Suitable for box fans: no, Suitable for roof fans: yes, Suitable for duct fans: no, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: no, Suitable for wall-mounted fans: no, Suitable for domestic fans: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no

Hygrostat HY 230 I Internal control elementFeatures:Made in Germany quality, protection class IP 30 for safety in the homeHygrostat - for simple controlInternal control element. Used for dehumidifying or humidifying closed rooms. The operating mode can be selected with a dip switch.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:The HY 230 or HY 230 I electronic hygrostat is used for dehumidifying or humidifying closed rooms. It is suitable for all living areas and commercial premises, including damp rooms such as bathrooms. Bathrooms (please observe protection class when installing), washrooms and drying rooms. The hygrostat uses an internal sensor to detect the room humidity and switches the fans, heat recovery units, humidifiers or dehumidifiers on and off depending on the set target value. The HY 230 or HY 230 I is either mounted directly on a flush-mounted box or mounted on the wall using the APM HY 230 surface-mounting set. The operating mode dehumidification (factory setting) or humidification can be set during commissioning using a DIP switch on the circuit board. A red LED in the housing indicates the switching status of the relay angezeigt.Artikel: HY 230 I, Voltage type: AC, Rated voltage: 230 V, Output: 230 V, Mains frequency: 50 Hz, Relative humidity measuring range: 20 % - 80 %, Installation type: Surface-mounted, Material: Plastic, Colour: Pure white, similar to RAL 9010, Weight: 0.0685 kg, Weight with packaging: 0.083 kg, Width: 71 mm, Height: 71 mm, Depth: 27 mm, Width with packaging: 75 mm, Height with packaging: 80 mm, Depth with packaging: 36 mm, Ambient temperature: 0 °C to 50 °C, Operating element: Internal, Sensor tolerance, relative humidity: 5 %, Switching differential, relative humidity: 2.5 %, Max. permissible switching current: 10 A / 4 A / cos phi = 1, 230 V AC / cos phi = 0.6, 230 V AC, Max. permissible inrush current: 16 A, Suitable for box fans: no, Suitable for roof fans: yes, Suitable for duct fans: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: yes, Suitable for wall-mounted fans: yes, Suitable for domestic fans: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no

Butterfly valve AP 100 white, automatic, DN100Features:Made in Germany quality, super quietAutomatic shut-off damper - for easy ventingWith concealed screw holes. Sealing tape included in the scope of delivery. External wall connection when using the WH 100 & 120 & 150 wall sleeve. Weather and UV-resistant plastic housingAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:Automatic closing flaps for ventilation. External wall connection when using wall sleeve WH 100 & 120 & 150. With concealed screw holes. Sealing tape included in the scope of delivery. Accessories: FG fly screen can be used. AP 100 B: Cover flap in brown. AP 150: With galvanised Schutzgitter.Artikel: AP 100, Air direction: Ventilation, Pressure loss: 10 Pa, Installation location: Wall, Material: Plastic, weather- and UV-resistant, Colour: Traffic white, similar to RAL 9016, Weight: 0.1139 kg, Weight with packaging: 0.123 kg, Flap type: Self-opening/closing, Damper type: Self-opening/closing, Damper type: Self-opening/closing, Damper type: Self-opening/closing. opening/closing, Suitable for nominal width: 100 mm, Width: 150 mm, Height: 150 mm, Depth: 50 mm, Width with packaging: 151 mm, Height with packaging: 151 mm, Depth with packaging: 51 mm, Ambient temperature: 60 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for ducted fans: no, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: no, Suitable for wall-mounted fans: no, Suitable for domestic fans: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no, With installation frame: no

Interval switch VZI 10 Run-on time 10 minFeatures:Made in Germany quality, protection class IP 40 for safety in the homeInterval switch - for simple operationFor regular ventilation of rarely used rooms. Switch-on delay 50 s, run-on time 10 min. Fan can be switched on by manual operation or switch. Interval time 1-15 h. Installation in flush-mounted box possible.Attractive design - compatible with any furnishing styleSuitable for continuous operation.Description:Interval switch for regular ventilation of rarely used rooms. Fan can be switched on via interval switch and manual operation. Can be operated using standard switches. Interval time adjustable: 1 h to 15 h. Installation in flush-mounted box possible. Test mark: VDE.Artikel: VZI 10, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Maximum load: 1.25 A, Protection rating: IP 40, Weight: 0.012 kg, Weight with packaging: 0.016 kg, Width: 20 mm, Height: 13 mm, Depth: 35 mm, Width with packaging: 20 mm, Height with packaging: 13 mm, Depth with packaging: 35 mm, Ambient temperature: 0 °C to 50 °C, Remote control: no, Run-on time: 10 min, Switch-on time: 10 min, Switch-on delay: 50 s, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Butterfly valve AP 100 B Automatic, DN100, brownFeatures:Made in Germany quality, super quietSelf-acting flap valve - for easy ventingWith concealed screw holes. Sealing tape included in the scope of delivery. External wall connection when using the WH 100 & 120 & 150 wall sleeve. Weather and UV-resistant plastic housingAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:Automatic closing flaps for ventilation. External wall connection when using wall sleeve WH 100 & 120 & 150. With concealed screw holes. Sealing tape included in the scope of delivery. Accessories: FG fly screen can be used. AP 100 B: Cover flap in brown. AP 150: With galvanised Schutzgitter.Artikel: AP 100 B, Air direction: Ventilation, Pressure loss: 10 Pa, Installation location: Wall, Material: Plastic, weather and UV-resistant, Colour: Chestnut brown, similar to RAL 8015, Weight: 0.113 kg, Weight with packaging: 0.345 kg, Type of flap: Self-opening/closing, Suitable for use with flyscreens. opening/closing, Suitable for nominal width: 100 mm, Width: 150 mm, Height: 150 mm, Depth: 50 mm, Width with packaging: 153 mm, Height with packaging: 153 mm, Depth with packaging: 52 mm, Ambient temperature: 60 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct fans: no, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: no, Suitable for wall-mounted fans: no, Suitable for domestic fans: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no, With installation frame: no

Door ventilation grille MLK 30 white white, length approx. 300 mmFeatures:Quality Made in GermanyDoor ventilation grille - for easy installationDoor cut-out: 275 x 105 mm, external dimensions: 295 x 120 mmAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:Door ventilation grille for bathroom, WC, kitchen. Free cross-section in accordance with FeuVo 80 and TRGI 86. MLK 30: Door cut-out: 275 x 105 mm, external dimensions: 295 x 120 mm. MLK 45: Door cut-out: 436 x 76 mm, external dimensions: 457 x 92 mm.Artikel: MLK 30 white, air direction: ventilation, installation: inside, installation location: door, material: plastic, plastic details: Polystyrene, PVC-free, Colour: white, Weight: 0.2 kg, Weight with packaging: 0.215 kg, Free cross-section: 164 cm2, Width: 290 mm, Height: 125 mm, Depth: 38 mm, Width with packaging: 300 mm, Height with packaging: 125 mm, Depth with packaging: 51 mm, Minimum door leaf thickness: 36 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: yes, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Internal lock, electr. AE 10/1 DN100Features:Made in Germany quality, super quiet, protection class IP X4 for safety in the homeElectric internal closure flap - for simple ventilation and extractionRegulation of basic ventilation through adjustable opening angle. Heat energy-saving as required. Control with switch, timers and overrun relay. Attractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:Internal flap for ventilation. Regulation of basic ventilation through adjustable opening angle. Heat energy-saving thanks to opening as required. Activation with commercially available off-switches, timers and overrun relays. Protection class IPX4. AE 10/1 can be combined with the window installation kit FE 100/1.Artikel: AE 10/1, Air direction: Ventilation, Voltage type: Alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz, Power consumption: 5 W, INenn: 25 mA, Protection rating: IP X4, Mains cable: 3 / 1.5 mm2, Installation: indoor, Installation location: wall / ceiling, Installation location: cellar, Installation type: surface-mounted, Installation position: vertical / horizontal, Material: plastic, Colour: traffic white, similar to RAL 9016, Weight: 0.31 kg, Weight with packaging: 0.418 kg, Flap type: electric, Nominal width: 100 mm, Suitable for nominal width: 100 mm, Width: 159 mm, Height: 159 mm, Depth: 85 mm, Width with packaging: 170 mm, Height with packaging: 170 mm, Depth with packaging: 110 mm, Ambient temperature: 40 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no, With installation frame: no

Mounting plate ZM 11 for small room fans in shaftFeatures:Quality Made in GermanyMounting plate - for easy installationFor installing ECA 100 small room fans in rectangular shaft openings. Can be adapted to any wall decor.Attractive design - compatible with any furnishing styleSuitable for continuous operation.Description:Mounting plate for the installation of MAICO small room fans in rectangular shaft openings. Adaptation to any wall decor (e.g. wallpaper) is possible. Wallpaper) mayglich.Artikel: ZM 11, Installation location: Duct, Installation type: Surface-mounted, Material: Plastic, Colour: Traffic white, similar to RAL 9016, Weight: 0.1 kg, Weight with packaging: 0.104 kg, Suitable for nominal width: 100 mm, Width: 160 mm, Height: 275 mm, Depth: 3 mm, Width with packaging: 160 mm, Height with packaging: 275 mm, Depth with packaging: 3 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

External grille SG 100 white, for aeration and ventilation, DN100Features:Quality Made in GermanyExternal grille - for easy installationWith concealed screw holes. Sealing tape included in the scope of delivery. External wall connection when using wall sleeve WH 100 & 120 & 150. Weather and UV-resistant plastic housingAttractive design with elegant front panel made of impact-resistant plastic - compatible with any interior style Suitable for continuous operation.Description:External grille for ventilation. External wall connection when using wall sleeve WH100 & 120 & 150. SG 100 & 120 & 150/1: With concealed screw holes. Fly screen accessories FG 100 & 120 & 150 can be used. SG 100 B: brown. SG 15: With galvanised protective grille. Sealing tape included in the scope of delivery. Replacement air filter for SG 120: SF 120.Artikel: SG 100, Air direction: Ventilation, Installation: Outside, Installation location: Wall, Installation type: Surface-mounted, Material: Plastic, Weather-resistant, UV-resistant, Colour: Traffic white, similar to RAL 9016, Weight: 0.1 kg, Weight with packaging: 0.127 kg, Suitable for nominal width: 100 mm, Width: 150 mm, Height: 150 mm, Depth: 51.5 mm, Width with packaging: 151 mm, Height with packaging: 151 mm, Depth with packaging: 55 mm, Ambient temperature: 60 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no, With wire mesh: no, With insect screen: no, With pressure relief damper, intake: no, With pressure relief damper, exhaust: no, With counter-rotating damper valve: no, With co-rotating damper valve: no, With installation frame: no, Lockable: no, Motorised: no

Spacer frame ECA-DR for ECA 100 iproFeatures:Quality Made in GermanySpacer frame - for easy installationFor the installation of ECA 100 ipro small room fans. Use of a frame makes cable routing possible. Fan can therefore also be installed in flat duct angle pieces. Do not install on windows or laminated glass. Scope of delivery: Spacer with 3 spacer frames, 4 100 mm wood screws, 4 dowels, 3 screws for fixing the fan and installation instructionsAttractive design - compatible with any interior styleSuitable for continuous operation.Description:Spacer frame for connecting small room fans from the ECA 100 ipro group. Use of a frame enables surface-mounted cable routing for ECA 100 ipro... devices. By using the ECA-DR, the small room fan can also be installed in flat duct angle pieces without overhang. Do not install on windows or laminated glass. Scope of delivery: Spacer with 3 spacer frames, 4 wood screws 100 mm, 4 dowels, 3 screws for fan fastening and Montageanleitung.Artikel: ECA-DR, Installation location: Wall / ceiling, Material: Plastic, Colour: Traffic white, similar to RAL 9016, Weight: 0.342 kg, Weight with packaging: 0.525 kg, Width: 153 mm, Height: 153 mm, Depth: 75 mm, Width with packaging: 158 mm, Height with packaging: 158 mm, Depth with packaging: 122 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Speed controller STSX 2.5 Rated voltage 230 V, infinitely variableFeatures:Made in Germany quality, protection class IP 30 for safety in the homeSpeed controller - for easy installationFor one direction of rotation for stepless regulation of fans. Green LED operating indicator. Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Speed controller for stepless regulation of fans. VDE-tested. For one direction of rotation. Installation on 35 mm standard profile rail possible. Green LED operating indicator. Due to the phase control technology, a physically induced humming noise can occur in the lower speed range. In rooms requiring low-noise fan operation, 5-step transformers TRE... ##########_0__: STSX 2.5, Voltage type: AC, Rated voltage: 230 V, Maximum load: 2.5 A, Minimum load: 0.1 A, Protection rating: IP 30, Installation type: Distribution panel / switch cabinet, Colour: Light grey, similar to RAL 7035, Weight: 0.0985 kg, Weight with packaging: 0.123 kg, Width: 35 mm, Height: 94 mm, Depth: 86 mm, Width with packaging: 40 mm, Height with packaging: 95 mm, Depth with packaging: 96 mm, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for tube ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: yes, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Wall sleeve WH 100 plastic, extendable, DN100Features:Quality Made in GermanyWall sleeve - for easy installationFor wall and ceiling mounting. Variable length.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Wall sleeve for wall and ceiling mounting. Variable length.Article: WH 100, Installation location: Wall / ceiling, Material: Plastic, Weight: 0.6 kg, Weight with packaging: 0.6 kg, Suitable for nominal diameter: 100 mm, Width: 114 mm, Height: 114 mm, Depth: 500 mm, Width with packaging: 114 mm, Height with packaging: 114 mm, Depth with packaging: 500 mm, Required core drilling: min. 115 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no