Maico centrifugal tube fan ERR 10/1 0080.0270

Temperature sensor for measuring the air temperature in air ducts. Combination with ETL 16 P, DTL 16 P, DTL 24 P möglich.Artikel: FL 30 P, Protection rating: IP 20, Installation location: Duct, Material: Plastic, Weight: 0.0783 kg, Weight with packaging: 0.082 kg, Width: 220 mm, Height: 140 mm, Depth: 20 mm, Width with packaging: 221 mm, Height with packaging: 141 mm, Depth with packaging: 21 mm, Temperature setting range: 0 °C to 30 °C, Suitable for box ventilators: yes, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: yes, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

AKE/1 - Brief informationControl unit AKE/1 incl. 2 pcs. AKE FFT humidity and temperature sensor (4m cable, can be extended on site to max. 30m) for fully automatic cellar dehumidification in conjunction with various fansAKE/1 - Product descriptionProduct featuresFully automatic, intelligent cellar dehumidification control for the highest demands.Permanent equalisation of the absolute humidity indoors and outdoors: Connected fans ventilate independently if the absolute humidity in the room is higher than outside.No maintenance or manual control required: install once and the system works automatically.Operation of fans up to a total (supply and extract air fan) of 600 W and 3 A.For the use of fans > 600 W and 3 A as well as three-phase fans, a circuit breaker must be installed between the control unit and the fan.Barrier-free product, as it switches on/off automatically without additional switches.Control unit monitors the room humidity via integrated humidity/temperature sensors.Frost protection function: system switches off at indoor temperatures below 5 °C.Additional manual operation for 30 minutes can be switched on and off again using a button on the control unit.No additional installation from the switch to the device necessary.Additional manual operation with external button or switch possible.Automatic button / switch detection.Status and function display via LEDs.Compact dimensions: Control unit 160 x 110 x 90 mm, outdoor sensor Ø50 mm, height 13 mm.Scope of delivery: Control unit, 2 sensors with 4 m cable length each.Sensor cable can be extended on site with LIYY 4x0.25 mm² cable to max. 30 (separate installation required).Housing made of impact-resistant plastic.IP protection: Control unit IP40 / outdoor sensor IP54.Frost protection: To prevent the room from cooling down, the AKE has a frost protection function. This automatically switches off the connected fan(s) at indoor temperatures of less than 5 °C.Garage dehumidification: optional switch-off of the frost protection function for unheated rooms.Suitable for continuous operation.Installation instructionsSimple installation: Wall mounting.Electrical connection: Surface-mounted.

Volume flow limiter for ventilation units and exhaust air systems. Simple insertion into DN 100 or DN 125 pipework. High control accuracy. Maintenance-free. Can be operated in any position. Fast and safe einstellbar.Artikel: VSB 100, Pressure range: 30 Pa - 300 Pa, Volume flow: 15 m3/h / 110 m3/h, Installation position: any, Housing material: plastic, Weight: 0.095 kg, Weight with packaging: 0.105 kg, Nominal diameter: 100 mm, Width: 110 mm, Height: 110 mm, Depth: 110 mm, Width with packaging: 111 mm, Height with packaging: 111 mm, Depth with packaging: 111 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Hygrostat HY 230 External control elementFeatures:Made in Germany quality, protection class IP 30 for safety in the homeHygrostat - for simple controlExternal control element. Used for dehumidifying or humidifying closed rooms. The operating mode can be selected using a dip switch.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:The HY 230 or HY 230 I electronic hygrostat is used for dehumidifying or humidifying closed rooms. It is suitable for all living areas and commercial premises, including damp rooms such as bathrooms. Bathrooms (please observe protection class when installing), washrooms and drying rooms. The hygrostat uses an internal sensor to detect the room humidity and switches the fans, heat recovery units, humidifiers or dehumidifiers on and off depending on the set target value. The HY 230 or HY 230 I is either mounted directly on a flush-mounted box or mounted on the wall using the APM HY 230 surface-mounting set. The operating mode dehumidification (factory setting) or humidification can be set during commissioning using a dip switch on the circuit board. A red LED in the housing indicates the switching status of the relay angezeigt.Artikel: HY 230, Voltage type: AC, Rated voltage: 230 V, Output: 230 V, Mains frequency: 50 Hz, Relative humidity measuring range: 20 % - 80 %, Installation type: Surface-mounted, Material: Plastic, Colour: Pure white, similar to RAL 9010, Weight: 0.0753 kg, Weight with packaging: 0.089 kg, Width: 71 mm, Height: 71 mm, Depth: 27 mm, Width with packaging: 75 mm, Height with packaging: 80 mm, Depth with packaging: 36 mm, Ambient temperature: 0 °C to 50 °C, Operating element: External, Sensor tolerance, relative humidity: 5 %, Switching differential, relative humidity: 2.5 %, Max. permissible switching current: 10 A / 4 A / cos phi = 1, 230 V AC / cos phi = 0.6, 230 V AC, Max. permissible inrush current: 16 A, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: yes, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Electronic temperature controller for controlling the electric air heaters ERH, DRH. With built-in sensor for measuring the room temperature. Optional control of supply air or room temperature possible. Triac controller with pulse packet control. Pulse period: 60s. Night setback by 0 K to 10 K below setpoint temperature possible. DTL 16 P: With additional input for minimum or maximum limitation of the supply air temperature. This requires combination with duct sensor FL 30 P. Accessories: Duct sensor FL 30 P for measuring the air temperature in ventilation ducts, room sensor FR 30 P for measuring in closed roomsumen.Artikel: DTL 16 P, Voltage type: Alternating current / Three-phase current, Rated voltage: 230 V / 400 V, Mains frequency: 50 Hz / 60 Hz, Maximum load: 16 A, Protection rating: IP 20, Installation type: Surface-mounted, Weight: 0.251 kg, Weight with packaging: 0.295 kg, Width: 93 mm, Height: 153 mm, Depth: 40 mm, Width with packaging: 95 mm, Height with packaging: 160 mm, Depth with packaging: 50 mm, Suitable for box fans: no, Suitable for roof fans: no, Suitable for duct fans: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: no, Suitable for wall-mounted fans: no, Suitable for domestic fans: no, Suitable for centrifugal fans: no, Suitable for circulation fans: no

Speed controller STX 1.5 Rated voltage 230 V, infinitely variableFeatures:Made in Germany quality, protection class IP 44 for safety in the homeSpeed controller - for easy installationStepless control. Minimum speed adjustable. Splash-proof. With LED operating indicator. Switch on the fan by turning the control knob. Includes spare fuse.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Speed controller for infinitely variable control of fans. Minimum speed adjustable. Can be used for surface and flush mounting, exception: STX 4 only for surface mounting. Functional principle: Phase angle control. Recommended distance from radio and television sets: 3 m. Switch on the fans at maximum speed by turning the control knob. Further turning reduces the speed. Splash-proof. Built-in temperature cut-out. Orange LED operating indicator. CE mark. Including spare fuse. Additional switching contact (230 V), e.g. for activating a flap. Due to the phase control technology, a physically induced humming noise may occur in the lower speed range. Therefore, in rooms requiring low-noise fan operation, use 5-step transformers TRE... for speed control. Installation on walls possible, avoid installation on ceilings due to temperature development. STX 1.5, STX 2.5: Width x height x depth when used for surface mounting: 82 mm x 89 mm x 69 mm, width x height x depth when used for flush mounting: 50 mm x 50 mm x 33 mm, STX 4: Width x height x depth when used for surface mounting: 82 mm x 89 mm x 69 mmArticle: STX 1.5, Voltage type: AC, Rated voltage: 230 V, Maximum load: 1.5 A, Minimum load: 0.1 A, Protection rating: IP 44, Installation type: Surface-mounted or flush-mounted, Colour: White, similar to RAL 9010, Weight: 0.1638 kg, Weight with packaging: 0.196 kg, Width: 82 mm, Height: 89 mm, Depth: 69 mm, Width with packaging: 85 mm, Height with packaging: 95 mm, Depth with packaging: 70 mm, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: yes, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Flat oval silencer RSOF 10/100 Length 1000 mm, DN100Features:Quality Made in GermanyFlat oval pipe silencer - for easy installationSuitable for low installation height. Consists of two-layer, flexible aluminium pipes. Inner pipe is finely perforated. There is an insulating layer of synthetic resin-bonded mineral fibre mat between the inner and outer pipe.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Flat, flexible telephony silencer in oval design. Suitable for low installation heights, its bendability enables adaptation even in difficult spaces and cable routing. The sound attenuators are made of two-layer, flexible aluminium tubes. The inner pipe is finely perforated. There is an insulating layer of 50 mm thick synthetic resin-bonded mineral fibre mat between the inner and outer pipe. The connection pieces have nipple dimensions and fit into pipes. Non-combustible in accordance with EN 13501 A1.Artikel: RSOF 10/100, design: 50 mm sound-absorbing packing, material: aluminium, weight: 1.538 kg, weight with packaging: 2.026 kg, nominal width: 100 mm, length: 1000 mm, width: 240 mm, height: 150 mm, depth: 1000 mm, width with packaging: 225 mm, height with packaging: 225 mm, depth with packaging: 1190 mm, ambient temperature: 200 °C, insertion loss at 63 Hz: 9 dB, insertion loss at 125 Hz: 7 dB, insertion loss at 250 Hz: 19 dB, insertion loss at 500 Hz: 24 dB, Insertion loss at 1 kHz: 42 dB, Insertion loss at 2 kHz: 56 dB, Insertion loss at 4 kHz: 34 dB, Insertion loss at 8 kHz: 31 dB, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Horizontal and vertical installation possible. Flow direction for vertical installation from bottom to top. With 2 counter-rotating damper halves made of aluminium. With circumferential seal. Non-return dampers open in the air flow and close via spring forceend.Artikel: AVM 10, Air direction: Ventilation or exhaust, Installation position: Vertical / horizontal, Material: Galvanised sheet steel, Weight: 0.187 kg, Weight with packaging: 0.3 kg, Damper type: Self-opening/closing, Nominal width: 0.5 kg, Weight with packaging: 0.5 kg, Weight with packaging: 0.5 kg, Damper type: Self-opening/closing, Damper type: Self-closing opening/closing, Nominal width: 100 mm, Width: 98 mm, Height: 98 mm, Depth: 88 mm, Width with packaging: 106 mm, Height with packaging: 106 mm, Depth with packaging: 97 mm, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Temperature sensor for measuring the air temperature in closed rooms. Combination with ETL 16 P, DTL 16 P, DTL 24 P möglich.Artikel: FR 30 P, Protection rating: IP 20, Installation type: Surface-mounted, Housing material: Plastic, Colour: Pure white, similar to RAL 9010, Weight: 0.075 kg, Weight with packaging: 0.09 kg, Width: 86 mm, Height: 86 mm, Depth: 30 mm, Width with packaging: 98 mm, Height with packaging: 98 mm, Depth with packaging: 37 mm, Temperature setting range: 0 °C to 30 °C, Suitable for box ventilators: yes, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: yes, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Mounting feet for mounting ERR fans on walls, ceilings or on Konsolen.Artikel: FUR 10/12/16, Installation location: Wall / ceiling, Material: Sheet steel, galvanised, Weight: 0.205 kg, Weight with packaging: 0.22 kg, Suitable for nominal width: 100 mm / 125 mm / 160 mm, Width: 293 mm, Height: 65 mm, Depth: 50 mm, Width with packaging: 180 mm, Height with packaging: 35 mm, Depth with packaging: 70 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Electric air heater for ventilation systems. With non-glowing tubular heating elements made of stainless steel. Operate with ETL/DTL temperature controller (see accessories). Increased risk of fire with dirty tubular heating elements. Install TFE air filter as a preventive measure. Recommended accessories: Duct sensor FL or room sensor FR, air flow monitor LW 9, contactor US 16 T and air filter TFE... . Safety instructions: Increased fire hazard with dirty tubular heating elements. Install TFE air filter as a preventive measure. Designed in accordance with VDE, appliance and product safety law and the relevant EU directives. With 2 independently switching temperature limiters. Minimum distance to flammable materials: 150 mm (install suitable insulation if distance is less): ERH 10-04, Voltage type: alternating current, Rated voltage: 230 V, Mains frequency: 50 Hz, IMax: 1.74 A, Protection rating: IP 43, Installation: indoor, Installation position: horizontal / vertical, Housing material: sheet steel, galvanised, Weight: 1.99 kg, Weight with packaging: 2.29 kg, Nominal diameter: 100 mm, Width: 100 mm, Height: 181 mm, Depth: 375 mm, Width with packaging: 260 mm, Height with packaging: 195 mm, Depth with packaging: 385 mm, Air heater type: electric, Heating output: 400 W, Suitable for box fans: no, Suitable for roof fans: no, Suitable for duct fans: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: no, Suitable for wall-mounted fans: no, Suitable for domestic fans: no, Suitable for centrifugal fans: no, Suitable for circulation fans: no

External grille MGR 80/125 V2A round, for pipe DN80 to DN125Features:Quality Made in GermanyExternal grille - for easy installationWith insect screen and spring holder. Attractive design - compatible with any interior style Suitable for continuous operation.Description:MGR: External grille for covering round ventilation openings. MGE: External grille for covering rectangular ventilation openings. With insect screen and spring holder. For duct diameters from 80 mm to 125 mm.Artikel: MGR 80/125 V2A, Version: round, Air direction: ventilation, Material: stainless steel, Weight: 0.1 kg, Weight with packaging: 0.112 kg, Outer diameter: 130 mm, Width: 130 mm, Height: 130 mm, Depth: 130 mm, Width with packaging: 130 mm, Height with packaging: 27 mm, Depth with packaging: 130 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Stainless steel air bonnet LH-V2A 10 for aeration and ventilation, DN100Features:Quality Made in GermanyAir bonnet for outside or exhaust air - for simple ventilation and extractionWith bird protection grille. For connection to outside air ducts, exhaust air ducts, extractor bonnets, tumble dryers, etc. Simple installation thanks to connection spigot and clamping spring. Without lip seal on the spigot and without condensate drainage edge.Attractive design - compatible with any interior style Suitable for continuous operation.Description:Air bonnet for ventilation and extraction. For connection to outside air ducts, exhaust air ducts, extractor bonnets, tumble dryers, etc. With connection spigot and clamping spring for easy installation. With bird protection grille. Without lip seal on the spigot and without condensate drainage edge. Especially when the air bonnet is used for exhaust air, on-site measures must be taken to ensure that any condensation water that may occur does not get onto the air bonnet. Condensation water must be prevented from running off the building facade, especially when the air hood is used for exhaust airuft.Artikel: LH-V2A 10, Air direction: Ventilation, Installation: Outside, Installation location: Outside wall, Material: Stainless steel, Colour: Stainless steel, brushed, Weight: 0.211 kg, Weight with packaging: 0.213 kg, Suitable for nominal width: 100 mm, Free cross-section: 63 cm2, Width: 150 mm, Height: 150 mm, Depth: 45 mm, Width with packaging: 151 mm, Height with packaging: 151 mm, Depth with packaging: 124 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Air filter for ventilation systems. Removable inspection flap for easy filter replacement. With synthetic fibre filter insert. Filter insert cannot be regenerated. With rubber seal on the air connection spigot. Accessories: Spare air filter FE... . Recommended accessories: Differential pressure switch DW 1000.Artikel: TFE 10-4, Installation position: Vertical / horizontal, Housing material: Galvanised sheet steel, Weight: 1.595 kg, Weight with packaging: 1.73 kg, Filter class: ISO Coarse 70 % (G4), Nominal width: 100 mm, Width: 205 mm, Height: 165 mm, Depth: 170 mm, Width with packaging: 240 mm, Height with packaging: 240 mm, Depth with packaging: 180 mm, Ambient temperature: 100 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: yes, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Hygrostat HY 230 I Internal control elementFeatures:Made in Germany quality, protection class IP 30 for safety in the homeHygrostat - for simple controlInternal control element. Used for dehumidifying or humidifying closed rooms. The operating mode can be selected with a dip switch.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:The HY 230 or HY 230 I electronic hygrostat is used for dehumidifying or humidifying closed rooms. It is suitable for all living areas and commercial premises, including damp rooms such as bathrooms. Bathrooms (please observe protection class when installing), washrooms and drying rooms. The hygrostat uses an internal sensor to detect the room humidity and switches the fans, heat recovery units, humidifiers or dehumidifiers on and off depending on the set target value. The HY 230 or HY 230 I is either mounted directly on a flush-mounted box or mounted on the wall using the APM HY 230 surface-mounting set. The operating mode dehumidification (factory setting) or humidification can be set during commissioning using a DIP switch on the circuit board. A red LED in the housing indicates the switching status of the relay angezeigt.Artikel: HY 230 I, Voltage type: AC, Rated voltage: 230 V, Output: 230 V, Mains frequency: 50 Hz, Relative humidity measuring range: 20 % - 80 %, Installation type: Surface-mounted, Material: Plastic, Colour: Pure white, similar to RAL 9010, Weight: 0.0685 kg, Weight with packaging: 0.083 kg, Width: 71 mm, Height: 71 mm, Depth: 27 mm, Width with packaging: 75 mm, Height with packaging: 80 mm, Depth with packaging: 36 mm, Ambient temperature: 0 °C to 50 °C, Operating element: Internal, Sensor tolerance, relative humidity: 5 %, Switching differential, relative humidity: 2.5 %, Max. permissible switching current: 10 A / 4 A / cos phi = 1, 230 V AC / cos phi = 0.6, 230 V AC, Max. permissible inrush current: 16 A, Suitable for box fans: no, Suitable for roof fans: yes, Suitable for duct fans: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: yes, Suitable for wall-mounted fans: yes, Suitable for domestic fans: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no

Protective grille for fans in accordance with DIN EN ISO 13857, suitable for fans with pipe connection spigots. Installation on intake and discharge side possibleglich.Artikel: SGR 10, Air direction: Supply and exhaust, Material: Wire, chromatised, Weight: 0.063 kg, Weight with packaging: 0.1 kg, Suitable for nominal width: 100 mm, Width: 100 mm, Height: 100 mm, Depth: 100 mm, Width with packaging: 100 mm, Height with packaging: 100 mm, Depth with packaging: 100 mm, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

External grille MGE 80/125 V2A square, DN80 to 125Features:Quality Made in GermanyExternal grille - for easy installationWith insect screen and spring holder. Attractive design - compatible with any interior style Suitable for continuous operation.Description:MGR: External grille for covering round ventilation openings. MGE: External grille for covering rectangular ventilation openings. With insect screen and spring holder. For duct diameters from 80 mm to 125 mm.Artikel: MGE 80/125 V2A, Design: rectangular, Air direction: Ventilation, Material: Stainless steel, Weight: 0.1 kg, Weight with packaging: 0.138 kg, Width: 150 mm, Height: 150 mm, Depth: 25 mm, Width with packaging: 151 mm, Height with packaging: 151 mm, Depth with packaging: 26 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

External grille MGR 80/125 white, round, for pipe DN80 to DN125Features:Quality Made in GermanyExternal grille - for easy installationWith insect screen and spring holder. Attractive design - compatible with any interior style Suitable for continuous operation.Description:MGR: External grille for covering round ventilation openings. MGE: External grille for covering rectangular ventilation openings. With insect screen and spring holder. For duct diameters from 80 mm to 125 mm.Artikel: MGR 80/125 white, Type: Round, Air direction: Ventilation, Material: Metal, Weight: 0.1 kg, Weight with packaging: 0.102 kg, Outer diameter: 130 mm, Width: 130 mm, Height: 130 mm, Depth: 133 mm, Width with packaging: 133 mm, Height with packaging: 25 mm, Depth with packaging: 133 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Flat oval silencer RSOF 10/50 Length 500 mm, DN100Features:Quality Made in GermanyFlat oval pipe silencer - for easy installationSuitable for low installation height. Consists of two-layer, flexible aluminium pipes. Inner pipe is finely perforated. There is an insulating layer of synthetic resin-bonded mineral fibre mat between the inner and outer pipe.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Flat, flexible telephony silencer in oval design. Suitable for low installation heights, its bendability enables adaptation even in difficult spaces and cable routing. The sound attenuators are made of two-layer, flexible aluminium tubes. The inner pipe is finely perforated. There is an insulating layer of 50 mm thick synthetic resin-bonded mineral fibre mat between the inner and outer pipe. The connection pieces have nipple dimensions and fit into pipes. Non-combustible in accordance with EN 13501 A1.Artikel: RSOF 10/50, design: 50 mm sound-absorbing packing, material: aluminium, weight: 0.94 kg, weight with packaging: 1.372 kg, nominal width: 100 mm, length: 500 mm, width: 240 mm, height: 150 mm, depth: 500 mm, width with packaging: 270 mm, height with packaging: 270 mm, depth with packaging: 820 mm, ambient temperature: 200 °C, insertion loss at 63 Hz: 2 dB, insertion loss at 125 Hz: 4 dB, insertion loss at 250 Hz: 11 dB, insertion loss at 500 Hz: 17 dB, Insertion loss at 1 kHz: 32 dB, Insertion loss at 2 kHz: 41 dB, Insertion loss at 4 kHz: 21 dB, Insertion loss at 8 kHz: 17 dB, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Mounting collars for sound and vibration damping of duct fans. With 10 mm thick Neoprenauflage.Artikel: ELR 10, Material: Sheet steel, galvanised, Weight: 0.164 kg, Weight with packaging: 0.2 kg, Suitable for nominal width: 100 mm, Width: 122 mm, Height: 122 mm, Depth: 60 mm, Width with packaging: 122 mm, Height with packaging: 122 mm, Depth with packaging: 60 mm, Suitable for box fans: no, Suitable for roof ventilators: no, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

CO2 sensor SKD Measuring range 500 - 2.000 ppm, 0 - 10 VFeatures:Made in Germany quality, protection class IP 20 for safety in the homeCO2 sensor - for a better indoor climateOptical sensor using infrared absorption. With 5 LEDs to display the CO2 concentration. Mounted on the inside wall, approximately at eye level.Attractive design - compatible with any interior styleSuitable for continuous operation.Description:CO2 sensor for controlling fans depending on the CO2 concentration. Optical sensor using infrared absorption. With 5 LEDs to display the CO2 concentration. With 0 V to 10 V output for outputting the CO2 concentration. With 0 V to 10 V output for temperature output. Do not use for safety-relevant gas measurements. Accessories: Safety transformer (230 V / 24 V) on site beschaffen.Artikel: SKD, Rated voltage: 14 V - 48 V DC / 16 V - 36 V AC, INenn: 0.02 A, IMax: 0.1 A, Protection rating: IP 20, Installation location: Wall, Installation type: Surface-mounted, Installation position: Any, Housing material: Plastic, Colour: Pure white, similar to RAL 9010, Weight: 0.095 kg, Weight with packaging: 0.132 kg, Width: 79 mm, Height: 120 mm, Depth: 30 mm, Width with packaging: 100 mm, Height with packaging: 135 mm, Depth with packaging: 40 mm, Ambient temperature: 10 °C to 40 °C, CO2 measuring range: 500 ppm - 2000 ppm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: yes, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

External grille MGE 80/125 white, square, DN80 to 125Features:Quality Made in GermanyExternal grille - for easy installationWith insect screen and spring holder. Attractive design - compatible with any interior style Suitable for continuous operation.Description:MGR: External grille for covering round ventilation openings. MGE: External grille for covering rectangular ventilation openings. With insect screen and spring holder. For duct diameters from 80 mm to 125 mm.Artikel: MGE 80/125 white, Design: rectangular, Air direction: ventilation, Material: metal, Weight: 0.1 kg, Weight with packaging: 0.145 kg, Width: 150 mm, Height: 150 mm, Depth: 25 mm, Width with packaging: 153 mm, Height with packaging: 153 mm, Depth with packaging: 26 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Speed controller STSX 2.5 Rated voltage 230 V, infinitely variableFeatures:Made in Germany quality, protection class IP 30 for safety in the homeSpeed controller - for easy installationFor one direction of rotation for stepless regulation of fans. Green LED operating indicator. Attractive design - compatible with any interior styleSuitable for continuous operation.Description:Speed controller for stepless regulation of fans. VDE-tested. For one direction of rotation. Installation on 35 mm standard profile rail possible. Green LED operating indicator. Due to the phase control technology, a physically induced humming noise can occur in the lower speed range. In rooms requiring low-noise fan operation, 5-step transformers TRE... ##########_0__: STSX 2.5, Voltage type: AC, Rated voltage: 230 V, Maximum load: 2.5 A, Minimum load: 0.1 A, Protection rating: IP 30, Installation type: Distribution panel / switch cabinet, Colour: Light grey, similar to RAL 7035, Weight: 0.0985 kg, Weight with packaging: 0.123 kg, Width: 35 mm, Height: 94 mm, Depth: 86 mm, Width with packaging: 40 mm, Height with packaging: 95 mm, Depth with packaging: 96 mm, Suitable for box ventilators: no, Suitable for roof ventilators: yes, Suitable for tube ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: yes, Suitable for domestic ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Air flow monitor for monitoring a minimum volume flow in ventilation systems. Length of the sensor cable: 2.5 m. If the sensor cable is laid in cable ducts, shielded cables must be used. The sensor detects the air flow and compares it with the setpoint value set on the control unit. Control unit: Installation on 35 mm profile rail. With LED function display for relay output and nominal voltage. Selector switch for operating and quiescent current function. With potential-free output via changeover contact, z.B. für Betriebs- oder Störmeldungen.Artikel: LW 9, Min. Strömungsgeschwindigkeit: 1 m/s, Max. Flow velocity: 20 m/s, Rated voltage: 230 V, Mains frequency: 50 Hz / 60 Hz, Maximum load (inductive load): 2 A, Maximum load (resistive load): 5 A, Protection rating: IP 10, Installation location: Duct, Weight: 0.343 kg, Weight with packaging: 0.455 kg, Width: 35 mm, Height: 90 mm, Depth: 65 mm, Width with packaging: 320 mm, Height with packaging: 115 mm, Depth with packaging: 95 mm, Fluid temperature at rated current: -20 °C to 80 °C, Ambient temperature: 60 °C, Suitable for box ventilators: yes, Suitable for roof ventilators: yes, Suitable for tube ventilators: yes, Suitable for heat recovery systems: yes, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for residential ventilators: yes, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Speed control system for controlling ventilation units/ventilators consisting of: 1 electronic infinitely variable speed controller (E-VSD), 1 control panel (CP-AQS) with integrated multi-sensor technology (°C / RH % / CO2 / VOC) Article: DRS, Voltage type: AC, Rated voltage: 220 V - 240 Vac, Mains frequency: 50 Hz / 60 Hz, Protection rating: IP X4, Colour: white, Weight: 0.63 kg, Weight with packaging: 0.77 kg, Width: 142 mm, Height: 88 mm, Depth: 80 mm, Width with packaging: 177 mm, Height with packaging: 125 mm, Depth with packaging: 95 mm, Suitable for box fans: no, Suitable for roof ventilators: yes, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Air filter for ventilation systems. Removable inspection flap for easy filter replacement. With synthetic fibre filter insert. Panel filter. Filter insert cannot be regenerated. With rubber seal on the air connection spigots. TFE ...-5: Filter class F5, accessories replacement filter RF...-5, TFE ...-7: Filter class ISO ePM1 50 % (F7), accessories replacement filter RF...-7, Recommended accessories: Differential pressure switch DW 1000.Artikel: TFE 10-7, Installation position: Vertical / horizontal, Housing material: Galvanised sheet steel, Weight: 4.1 kg, Weight with packaging: 4.6 kg, Filter type: Dust and pollen filter, Filter class: ISO ePM1 50 % (F7), Nominal width: 100 mm, Width: 360 mm, Height: 300 mm, Depth: 300 mm, Width with packaging: 405 mm, Height with packaging: 405 mm, Depth with packaging: 410 mm, Ambient temperature: 80 °C, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: yes, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

5-step transformer for speed adjustment. For controlling alternating current fans. With operating indicator light. Additional switching contact (230 V) e.g. for controlling a Klappe.Artikel: TRE 0.4-2, voltage type: alternating current, rated voltage: 230 V, mains frequency: 50 Hz / 60 Hz, rated power: 72 W, maximum load: 0.4 A, protection class: IP 54, secondary voltage: 85 V / 115 V / 150 V / 180 V / 230 V, Installation type: surface-mounted, Housing material: plastic, Colour: light grey, similar to RAL 7035, Weight: 1.445 kg, Weight with packaging: 1.96 kg, Width: 195 mm, Height: 148 mm, Depth: 175 mm, Width with packaging: 235 mm, Height with packaging: 235 mm, Depth with packaging: 195 mm, Ambient temperature: 0 °C to 40 °C, Suitable for box fans: no, Suitable for roof fans: yes, Suitable for duct fans: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted fans: yes, Suitable for wall-mounted fans: yes, Suitable for domestic fans: yes, Suitable for centrifugal fans: no, Suitable for circulation fans: no

External grille MGE 80/125 aluminium square, DN80 to 125Features:Quality Made in GermanyExternal grille - for easy installationWith insect screen and spring holder. Attractive design - compatible with any interior style Suitable for continuous operation.Description:MGR: External grille for covering round ventilation openings. MGE: External grille for covering rectangular ventilation openings. With insect screen and spring holder. For duct diameters from 80 mm to 125 mm.Artikel: MGE 80/125 alu, Design: rectangular, Air direction: ventilation, Material: aluminium, Weight: 0.079 kg, Weight with packaging: 0.1 kg, Width: 150 mm, Height: 150 mm, Depth: 30 mm, Width with packaging: 153 mm, Height with packaging: 153 mm, Depth with packaging: 31 mm, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for duct ventilators: no, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no

Water/air heater for ventilation systems. Copper connections. Housing cover can be removed for maintenance work. With rubber gasket on the air-Anschlussstutzen.Artikel: WRH 10-1, Installation position: vertical / horizontal, Housing material: galvanised sheet steel, Weight: 3.45 kg, Weight with packaging: 3.71 kg, Nominal diameter: 100 mm, Free cross-section: 1012 cm2, Width: 225 mm, Height: 183 mm, Depth: 380 mm, Width with packaging: 265 mm, Height with packaging: 205 mm, Depth with packaging: 381 mm, Air heater type: Water, Heating output: 1300 W, Mass flow: 55 kg/h, Flow temperature: 70 °C, Return temperature: 50 °C, Max. Water temperature: 100 °C, Max. Water pressure: 6 bar, Water pressure difference: 500 Pa, Suitable for box ventilators: no, Suitable for roof ventilators: no, Suitable for tube ventilators: yes, Suitable for heat recovery systems: no, Suitable for wall-mounted ventilators: no, Suitable for wall-mounted ventilators: no, Suitable for domestic ventilators: no, Suitable for centrifugal ventilators: no, Suitable for circulation ventilators: no